How do you adjust the clutch on a Honda?
This is usually held in place with a bolt and horseshoe device remove the bolt and the internal part and leave just the outer in the casing get planty of thin oil/kerosene mix in and leave for a while. Then if it still wont move GENTLY tap with a rubber hammer with the casing supported this should free it up.
What kind of wiring harness does a Honda CG125 use?
Honda CG125 CG 125 Electrical Wiring Harness Diagram Schematic 1976 – 2008 HERE Honda CL72 250 Scrambler Electrical Wiring Harness Diagram Schematic 1962 – 1965 HERE Honda CL90 Scrambler CL 90 Electrical Wiring Harness Diagram Schematic 1967 – 1969 HERE Honda CL125 Scrambler CL 125 Electrical Wiring Harness Diagram Schematic 1967 to 1974 HERE
What kind of wiring harness does a Honda CB175 use?
Honda CB160 CB 160 Electrical Wiring Harness Diagram Schematic 1965 1966 1967 HERE Honda CB175 K0 CB 175 Electrical Wiring Harness Diagram Schematic 1968 HERE Honda CB175 K3 CB 175 Electrical Wiring Harness Diagram Schematic 1969 HERE Honda CB175 K4 CB 175 Electrical Wiring Harness Diagram Schematic 1970 HERE
How to adjust spark plugs on CB CL77?
Remove the point cover, spark plugs & stator cover. Set the right piston to TDC, and using the T mark, adjust the right valves first. Loosen the 10mm nut first and then adjust the set-screw. “Trick” is to tighten the set-screw so that it just pinches the .004″ “feeler” gauge & then back it off so that the gauge barely slides in & out.
Remove the point cover, spark plugs & stator cover. Set the right piston to TDC, and using the T mark, adjust the right valves first. Loosen the 10mm nut first and then adjust the set-screw. “Trick” is to tighten the set-screw so that it just pinches the .004″ “feeler” gauge & then back it off so that the gauge barely slides in & out.
What’s the best way to remove a CL77 pipe?
For CL77 pipe install or removal: Remove the LEFT side header pipe exhaust studs (using 2 locked-together 10mm nuts) so as to clear the frame as you “swing” the engine into the frame cradle. Also use the thin gasket material or duct tape wrapped around the frame tubes to protect from motor scratches!!
When to use synthetic oil on Honda CL77?
Use “synthetic oil” only after the rings “seat” (after 2,000-plus miles) and with new engine case seals (old seals tend to “weap” with synthetic more easily). Synthetic oil terminates any “seating” process(es) for valves or rings! (6a) ENGINE OIL: Recommend HONDA M/C Oil (10W-40) or SPECTRO Regular or DURABLEND.
What’s the best way to set a CB / CL77?
Valves are done COLD with a 10mm wrench and the special holder that comes with the CL/CB77 tool kit. Remove the point cover, spark plugs & stator cover. Set the right piston to TDC, and using the T mark, adjust the right valves first. Loosen the 10mm nut first and then adjust the set-screw.
This is usually held in place with a bolt and horseshoe device remove the bolt and the internal part and leave just the outer in the casing get planty of thin oil/kerosene mix in and leave for a while. Then if it still wont move GENTLY tap with a rubber hammer with the casing supported this should free it up.
What’s the torque for a secondary clutch bolt?
for the new secondary (driven) clutch bolt is: Step 1 torque bolt to 15 ft/lbs +/- 1ft/lbs. Step 2 tighten; 180 degrees +/- 5 degrees. Step 2 – Tighten retaining nut another 180 degrees +/- 5 degrees.
How do you remove the clutch from a Harley Davidson?
Next, remove the outer primary cover & gasket and slacken the clutch cable. Loosen the jam nut and back off on the Harley clutch adjustment at the clutch pack. Remove the adjuster plate retaining clip to expose the mainshaft/clutch hub nut. Now is a good time to sneak a long tie wrap around the primary chain adjusting shoe.
What’s the best way to remove a clutch basket?
As usual, Bob starts with the battery negative cable disconnected and the drive, drained. It is always a good idea to let the drive compartment drain overnight, if possible. This helps you to work cleaner, without so much residual oil hanging around. Next, remove the outer primary cover & gasket and slacken the clutch cable.