Which is Crane Cams single fire ignition coil?
The Crane Cams Single Fire Ignition Coil part number 8-3001 is intended for Harley-Davidson® applica- tions with aftermarket single fire ignitions such as the Crane HI-4 series that require a 3 ohm resistance coil. The 8-3001 is molded in solid epoxy to eliminate vibration and arcing damage.
How to install an electronic single fire ignition?
INSTALLATION INSTRUCTIONS FOR ELECTRONIC SINGLE FIRE IGNITION PART NO. 53-50 Installation instructions for street application using 1970 & later coils with 5 ohms of primary resistance. If installing in a race application, you may use 3 ohm coils. 1. Remove old ignition. 2. Lubricate the new advance assembly shaft lightly with oil.
What is part number for single fire ignition coil?
SINGLE FIRE IGNITION COIL Part Number 8-3001 WARNING: Do not perform any work or disconnect any part of the ignition system without first disconnecting the battery ground cable. WARNING: Do not come into contact with the coil primary wires or the sec- ondary plug wires while the engine is running.
How to test an electric single fire engine?
Turn on the ignition and hold the ignition rotor counterclockwise into advanced position with the weights against the stops. Then slowly rotate the engine forward until the test light brightens. Check in the timing hole to see that the front cylinder’s advance mark is centered. If it is, go on to Number 4 below. 3.
The Crane Cams Single Fire Ignition Coil part number 8-3001 is intended for Harley-Davidson® applica- tions with aftermarket single fire ignitions such as the Crane HI-4 series that require a 3 ohm resistance coil. The 8-3001 is molded in solid epoxy to eliminate vibration and arcing damage.
SINGLE FIRE IGNITION COIL Part Number 8-3001 WARNING: Do not perform any work or disconnect any part of the ignition system without first disconnecting the battery ground cable. WARNING: Do not come into contact with the coil primary wires or the sec- ondary plug wires while the engine is running.
How does a Harley Davidson single fire ignition work?
Removing the original coil is simple, but installing new duals may take some patience when routing the wiring. Once installed it was time for a test ride. The engine started immediately and settled to an even idle. Much of the original vibration is gone. Starting off the throttle response is smooth and slightly higher.
How big should the cams be on a 1984 EV?
Cams for 1984-’87 engines should measure 3.025 inches from front face of gear to thrust shoulder surface. Cams for ’88 and later EV engines need to be shimmed to 3.075 (+.050 longer) because of a factory design change in the length of all ’88 and later camshafts. Proper end play for installed camshafts is .010 /.015 inches.
Can a single plug ignition be used on a hi-4?
COIL AND SPARK PLUG CABLE CONSIDERATIONS We recommend replacing the O.E. coil. Coils used with the HI-4 must have at least 2 ohms primary resistance. Coils with 4 ohms or higher may be used, but may not produce optimum output. We rec- ommend the following coils for single and dual-plug applications: HI-4 Ignition With Single Plug Heads.
How do you install a crane ignition coil?
Install the new Crane coil as shown in Figure 5 or 6. If your model has a coil cover attached to a side cover, remove the three screws holding the coil cover. Discard the three small plastic spacers and reattach the coil cover to the side cover. 6. Refer to Figure 7 or 8 for coil primary hookup details. Route the spark plug wires to the spark
Install the new Crane coil as shown in Figure 5 or 6. If your model has a coil cover attached to a side cover, remove the three screws holding the coil cover. Discard the three small plastic spacers and reattach the coil cover to the side cover. 6. Refer to Figure 7 or 8 for coil primary hookup details. Route the spark plug wires to the spark
COIL AND SPARK PLUG CABLE CONSIDERATIONS We recommend replacing the O.E. coil. Coils used with the HI-4 must have at least 2 ohms primary resistance. Coils with 4 ohms or higher may be used, but may not produce optimum output. We rec- ommend the following coils for single and dual-plug applications: HI-4 Ignition With Single Plug Heads.