Why does my mobility scooter keep stopping?
A lot of times when the mobility scooter cuts off, the gauge on the battery drops to zero. The most common reason for a fast-depleting battery is age. As batteries age, they store less charge and are less efficient. So not only do they lose their charge faster, they have little of it to begin with.
Why is my Gogo scooter not working?
Check that the batteries are fully charged. Push in the main circuit breaker reset button. Make certain that the battery pack is seated properly. Be sure the power down timer feature has not been activated.
Why is my electric scooter cutting out?
A lot of times when the mobility scooter cuts off, the gauge on the battery drops to zero. This could mean one of two things: that the battery is actually depleted or that it still contains charge but there is an electrical problem somewhere causing the gauge to drop. If it’s a new battery, it might be faulty.
Why does my Shoprider mobility scooter keep cutting out?
For example, if the motor is going bad, it will not just stop abruptly, it will usually start to slow down or even make some noise before turning off. In other rare circumstances, it could be a loss of signal due to a wire getting cut or disconnected somewhere between the controller and the motor.
Why is my scooter beeping and not moving?
Beep Codes. Condition: The battery voltage is to low and can not power up the scooter. Solution: Replace charge the scooter completely, or replace the batteries. Condition: The battery voltage is to high and the scooter can not operate.
Why is the green light flashing on my mobility scooter?
If the charging indicator is green, this means the battery is fully charged. In this case, the battery charger must be disconnected from the battery so as not to cause overcharging. If the charging indicator is flashing alternate red/green, this indicates there is an electrical problem with the battery pack.
Why is my mobility scooter not working properly?
Your mobility scooter might not have any battery problems at all. It might be something simple that is what stops the scooter from working. Without you even realizing it, the kill switch on your scooter is what is causing the trouble.
Why is the Kill Switch on my electric scooter not working?
So, when you again want to ride the scooter the next day, it might be still on which is why the aovo pro or any other scooter with the kill switch is not working. Just turn it off and try again to get the engine running. There is no doubt that the scooters that run on the battery are exceptional. But they come with their troubles.
Why is there no green light on my mobility scooter?
It appears that because there is no green light showing, there may be a problem with the motor or a wire that has become disconnected somewhere. I would dis-assemble the scooter and check that all the connections are ok and do continuity tests on each cable with a multimeter before checking the state of the motor brushes.
Is it safe to go over 30 km / h on electric scooter?
There are other reasons for this limitation, safety being one of them. It’s not safe going with more than 30 km/h on an electric scooter. The risk of injury is very high as you can easily lose your balance and fall. Always wear protective gear. Not all scooters can go over the manufacturer speed limitation.
What’s the problem with my GO GO scooter?
Condition: The throttle or potentiometer or the speed pod has malfunctioned. Solution: Contact Statewide Mobility to replace both devices at a low cost. Condition: The Go Go scooter’s motor has been disconnected. Solution: Contact Statewide Mobility for further assessment of your mobility scooter.
Which is the best GO GO scooter to buy?
The Pride Mobility Go-Go scooter is the most popular mobility scooter on the market. Understanding your product will save you time and money when an issue arises. All Go-Go scooters have a troubleshooting diagnostic beep, that allows you to figure out what to look for in order to fix your scooter. The beep codes range from 2-9 beeps.
How to diagnose a pride GO GO scooter?
When diagnosing your scooter it is very important to made sure your scooter is fully charged, and you have unplugged the charger. Now what you want to do is turn the get on and listen for the beep. Count how many beeps you hear. If you missed the count, don’t worry, it will repeat until you turn the mobility scooter off.
What to do if your GO GO scooter has been disconnected?
Condition: The Go Go scooter’s motor has been disconnected. Solution: Contact Statewide Mobility for further assessment of your mobility scooter. Condition: Possible controller trip. The scooters battery pack may have been put in place while the key was inserted. Solution: Turn off the scooter. Insert the battery pack. Turn on the scooter.