Why does my bike make a clicking noise when I start it?

This post is to explain what the noise is and why it happens. The starter motor on a bike uses a lot of power to turn the engine. The starter button cannot handle the current that the starter draws from the battery so a large electric switch called a solenoid is used.

Why does my motorcycle start when I turn the key?

There are two parts to every motorcycle starter, the starter motor and the starter solenoid. The solenoid is a little magnet and when you turn the key, it shoots out a small gear that the magnet polarizes. Essentially, this gear starts turning which in turn starts rotating the flywheel in the engine.

What to do when your bike won’t start?

If you have a set of jump leads or a booster pack you could try putting the -ve one on the exhaust someplace and the +ve to the starter motor connection. Make sure you are in neutral first. If this causes the starter to spin then you have an electrical connection fault. If not, the starter is faulty.

Where is the starter button on an electric car?

The starter button cannot handle the current that the starter draws from the battery so a large electric switch called a solenoid is used. The solenoid can always be found by following the heavy wire from the battery + terminal.

What does it mean when your bike won’t start?

I checked my starter as per bobf, jumped the connection where the positive battery cable connects and the one where the solenoid connects to starter motor, and the starter whines- so my contacts must be on their way out. I’m guessing that’s what that means.

What does it mean when Your starter clicks but wont start?

Today’s topic is “starter clicks but won’t start.” Here are the steps to check that you got a faulty starter. Number one. First start by checking for battery power. Turn on your headlights, and if the light is bright that means you got power. If it is not bright then you got a bad battery or a faulty alternator.

What to do when motor just clicks when trying to start?

I sprayed the starter gear with WD 40 and moved up and down by hand has worked fine ever since. Its worth a shot. Re: Motor just clicks when trying to start?? HELP

What should I do if my bike wont start?

Charge the battery or replace it if it’s dead. Am easy way to test your battery is by checking the voltage-drop with a multimeter as you try starting the bike. If your fully charged battery drops below 11,5 volts under load (while you crank the starter), it needs to be replaced.

Why does my bike not start with a side stand down?

With leaks—whether from cracking, rot, or road damage—you might be able to reseal the line, or you may need a replacement before you’re road-worthy again. Newer bikes (and some older ones) may refuse to start with the side stand down.

What kind of sound does a bike bell make?

The sound made by the bike bell is loud and crisp, but not too high, as not to scare the people on the road, but enough to let them know that you are in the area.

How can I tell if my motorcycle battery is good?

Now push the start button and watch what the voltage drops to. It doesn’t matter if the bike starts or not, what you’re looking for is a voltage reading. A healthy 12 volt motorcycle battery should maintain a range from 9.5 – 10.5 volts under the load for a good 30 seconds straight.

What kind of batteries do I need for my electric bike?

There are four 12 volt batteries which you can add to, or take out of, a series, depending on what your conversion kit requires. This gives you the flexibility to adapt your battery to your voltage needs, but isn’t as neat and discreet as the lithium batteries above.

Why does my electric bike make a crackling noise?

The crackling only begins when both battery and speed controller are on together, if the battery is switched on without controller then there is no crackling from battery. I haven’t dropped my bike or got it soaked in the rain or anything else that might have caused the issue. Its just suddenly appeared.

Why does my battery make a sizzling sound?

The idea is for when the battery is gassing under charge/load (as they all do to an extent), it dispels the fumes away from that enclosed space.

How are the batteries on an electric bike determined?

You’ll feel like you’re riding a traditional bike, only with the legs of a superhero! E-bike batteries vary in capacity; the bigger the battery, the faster and/or farther you can travel. To determine what the battery power is, take a look at the watt hours (Wh). The higher that number, the more power capacity the battery has.

What should I do if I hear a noise on my bike?

To check, grab your front brake lever and rock the bike front to back. If the headset is loose, you should be able to feel movement. Solution: Loosen your stem bolts and tighten your headset bolt. Once you’ve tightened the headset, secure your stem bolts and check using the brake lever test.

What causes a click on a car starter?

This can be an intermittant problem where it just sticks. It’ll cause that click and nothing else will happen. It’s a typical problem and you can usually even buy a new solenoid to put on your starter. Takes a little extra time, but the solenoid is typically much less than a new starter.

Why does my bike keep clicking the start button?

Took the battery to local auto parts store and checked out just fine with good charge. Put battery back in and hit start same click sound. After repeatedly clicking the start button I tracked the sound to the starter relay. Well with one hand moving the relay around and one pushing the start button bike would start up.

Why does my motorcycle make a clicking noise?

You go out to your motorcycle, put in the key, and try to start it only to hear those annoying and dreaded clicking noises instead of the rumbling of the engine. Those clicking noises can ruin someone’s day pretty quickly. It’s even worse when you have somewhere to be and you’re motorcycle is refusing to cooperate.

Why do my pedals click once per crank Rev?

Pedal threads can get dirty from time to time. Removing pedals, cleaning threads and reinstalling is often a sure fire way to cure a pedal click. My new pedals – M540’s – required a bit of grease after just a couple of months it wasn’t difficult to do

What to do if your Harley Davidson won’t start?

Try looking under the Seat or the left side cover . if the thing clicks look for the clicking were it’s coming from . Okay thanks sounds like a plan. Start simple. Like SCHMIDTYS said, clean, tight connections. A little sand paper or a wire brush on the posts and connectors and a screwdriver is all you need.

Why does my bike make the same clicking sound?

Put battery back in and hit start same click sound. After repeatedly clicking the start button I tracked the sound to the starter relay. Well with one hand moving the relay around and one pushing the start button bike would start up. After that I put off fixing it for a while and had been starting it the same way. That was until yesterday.

Why does my bike starter keep clicking repeatedly?

Anyway I came back to the house and hooked my battery charger straight to the power and ground battery cables on the bike and set it to the 50 amp position on the charger for starting and gave it a go. Still same thing charger just clicks repeatedly. It has the power for sure because that charger can start a car.

Why does my car make a clicking sound when I start it?

Thought maybe its the battery. Took the battery to local auto parts store and checked out just fine with good charge. Put battery back in and hit start same click sound. After repeatedly clicking the start button I tracked the sound to the starter relay.

How do you find the solenoid on a bike?

The solenoid can always be found by following the heavy wire from the battery + terminal. If the battery is healthy, when you press the starter button it sends a small electrical current to the solenoid which pulls in a contact with a heavy ‘click’ and supplies the heavy current to the starter motor.

What makes a dirt bike hard to start?

If the top end is worn out, or there’s a gasket that’s not sealing (ie: blown head gasket, leaking base gasket) the motor could be low on compression, and low compression certainly will make an engine hard to start, if you can get it running at all.

What should I do if my solenoid does not click?

Before you go spending money check the HD wiring. Battery to solenoid to starter also any earth straps, engine to chassis, battery to chassis. Remove them and clean with a wire brush so they are 100% clean. getting the selonoid to click makes me think your starter is likely the problem.

Why does my selonoid starter light not click?

getting the selonoid to click makes me think your starter is likely the problem. Just my guess. You obviously have power to the solenoid. Hook the clamp end of your test light to an engine ground then touch the test light to the starter post with the switch in start position. If you get no response to your test light the solenoid contacts are bad.

Why does my car make a clicking noise when I turn the key?

Although a clicking sound can come from other sources such as the suspension, the most frequent and familiar clicking comes after turning the key or pressing the ignition button. There might be a sluggish single click or there might be a jarring spray of clicking, and both are symptoms of parts asking for assistance.

What should I do if my motorcycle battery wont start?

If the reading says anything close to or slightly below 12 volts, charge your battery and try starting your motorcycle again. If it has a really low number, such as 9 volts or below, then you battery is pretty much toast and you’ll need to purchase a new one.

What’s the problem with my bike not starting?

Bike won’t start, battery is fine I just joined the sight because I really need some help. I am a first time owner and have a 2005 Suzuki GSX600F Katana with 12,000 miles. It has been good to me besides recently. I started it up a few days ago, went to put it in first gear from neutral and it shut off. It would not start up there after.

What happens when you push the start button on a bike?

When you push the button it gives power to the starter to crank the motor. When you push start the bike, with it in gear you crank the motor manually, so check the connection (s) at or around the start button. As for the clutch hmmm does it engage, as in when you pull in the lever does it work as intended?

Why is my razor electric dirt bike not working?

Razor Electric Dirt Bike Click Noise But Not Working FIX – This Could Be Your Problem! If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

Why does my car click when I Turn on the ignition?

If you hear a clicking sound after turning the ignition key, then it is possible that the vehicle’s starter is broken. In other scenarios, there would be no clicking sound and the starter just gets damaged. Some of the other symptoms of a broken starter are when smoke coming out of the engine or seeing oil under the engine.

Why does my motorcycle not start when I turn it on?

Clogged Injector Symptoms of a clogged injector: Your motorcycle will attempt to turn over normally when you try to start it but there won’t be any combustion. If you know it’s sparking correctly and that there is gas in the tank but it has been sitting for a while, your culprit is probably a clogged fuel injector.

Why is my ignition not working on my motorcycle?

Turn the key to the first click and see if the neutral light comes on. If the light doesn’t come on then this suggests that there is a problem with the ignition switch itself. If this is the case then the entire switch needs to be replaced. If your motorcycle is difficult to start but does start eventually then this could be due to corrosion.

If you don’t see these symptoms or are otherwise unsure what to look for, the first step is ensuring that the battery is operational and providing the maximum voltage. To confirm your battery is still good, you should visually inspect it, check the voltage, and load test the battery. A visual battery inspection should involve:

Why does my car make a clicking sound when I start the engine?

Repeated “clicking” sounds usually indicate a dead battery. But a faulty solenoid that fails to make adequate electrical contact inside can also produce this tell-tale sound. 4. Sometimes a bad starter solenoid, instead of preventing the engine from starting, may cause it to start on its own without the key being turned to the “start” position.”

Why does my starter click over and over?

The clicking can be from dirty connections, here’s why. A dirty connection can make contact and allow the current to flow. As the current increases the dirty connection can’t keep up and the connection causes a high resistance causing the current to drop. Once the current drops the connection can then flow enough to start over.

Why does my solenoid make a clicking sound?

This could mean that the solenoid is trying to engage but that the internal components are stuck and unable to work properly. 3. Repeated “clicking” sounds usually indicate a dead battery. But a faulty solenoid that fails to make adequate electrical contact inside can also produce this tell-tale sound. 4.

What causes a motorcycle starter to go bad?

A motorcycle starter goes bad usually because of age. Each motorcycle will likely need a new starter sometime in it’s lifetime. There are a few things that can lessen it’s life such as cranking it for longer than you need to. That can cause electrical connections to overheat and melt.

Why does the solenoid make a clicking noise?

If things were all good prior and the lights are dimming when the starter button is depressed that seems to suggest power is in the solenoid relay (the electro magnet that pull the internal bar across the solenoid poles,battery to starter) circuit. It sounds like the solenoid is bad or its relay anyway if it cranks when the poles are jumped.

Why is my solenoid not clicking on adventure rider?

If the solenoid does not click then it is as up the page,power is not getting to the terminals that activate the solenoid electro magnet. (from the starter button circuit) If a known good switch does not work,check the clutch lever where it activates the switch. The problem may be at the lever,not the switch.

What does a solenoid do on a bike?

Most bikes have no solenoid to engage the starter to the flywheel like a car, they have constant mesh with the crank through a sprauge clutch (catches one way, slips the other). Click to expand… There’s still a solenoid who’s job is to connect the battery to the starter; often called a starter relay. If there were

What does it mean when your car makes a clicking sound?

A clicking or clattering sound while in motion may also indicate a primary drive chain in need of adjustment. A mechanic’s stethoscope can help pinpoint the location of a new, troubling sound. Locating the precise source of some engine noises can be tricky, but very helpful in sorting out what needs to be done.

Why do I hear strange noises on my motorcycle?

While a brand new motorcycle may sound the alarm with the same kind of odd sounds, these noises may be more likely to occur if you ride a vintage or high-mileage motorcycle. The video could not be loaded, either because the server or network failed or because the format is not supported.

Why does my motorcycle make a grinding noise when I brake?

An intermittent grinding noise, very often inconsistent in occurrence and sometimes accompanied by a new vibration in the handlebars under braking may be pretty easy to track down; front or rear brake pads in need of replacement. This can also arise from a caliper sticking causing a brake pad to drag.

What to do when you hear noise on your bike?

For example, if you think the noise is coming from a wheel, install a different one (ask to borrow a friend’s if you don’t have a spare) and see if the noise goes away. If so, you know your noise is wheel related, which will make it much easier to find it.

Why do I hear a clunk when I pedal my bike?

If you hear or feel a clunk when pedaling, it’s probably caused by a loose bottom bracket or pedal. Solution: Check the latter with a pedal wrench, tightening both pedals. The right one is turned clockwise to tighten, the left is turned counterclockwise (more pedal information here).

Why does my bike chain make a squeaking noise?

One common constant squeaker is a poorly lubricated chain. Solution: Inspect yours. If the rollers are dry and shiny, apply drip or spray lube. On extra dry ones it may take a while for the substance to penetrate and silence the noise. Then keep the chain quiet by lubing it every 2 weeks. Always wipe off the excess to minimize sludgy build-up.

Why does my bike make a clicking noise?

The clicking noise when pedaling bike you hear could be caused by loose cassette cogs. Use a cassette locking tool and an adjustable wrench to tighten the cogs and eliminate the clicking sounds. 5. Check the Pedals and Bottom Bracket

How can I tell if my pedals are clicking?

With a square taper BB you can put the cranks back in 90° increments. If you put them back by 180° you can find out if the clicking happens now with the left crank forward. Which would point to a fault with the BB. If it’s still the right crank fw it would point to the chainrings.

Why does my bottom bracket click when I pedal?

Since the noise started, I have reinstalled the cranks, tightened chainring bolts, and replaced the seatpost, pedals and wheels. The bottom bracket rotates smoothly when cranks are not installed or without chain. The click only occurs when pedaling with force, and happens when standing up so it very probably is not the saddle or seat post.

What to do when your bike pedals hard?

A few things to do to isolate the problem to the bottom bracket: Make sure you also hear the noise when standing up (Yes, I know you replaced the seatpost, but it might be the seat. Maybe.) When you pedal hard, you also exert more force on the handlebar. Try yanking the handlebar every which way while stopped.

What should I do if my motorcycle turn signal is not working?

I let out an “…uh?” just loud enough to be audible, but silent enough that Steve, no doubt feeling sorry for the clueless putz on the phone gave some instructions: “Before you go ripping everything apart, unscrew the turn signal lens and take it off.

Navigation