Why is my turn signal not flashing on my Fatboy?
Had the same problem on a 99 Fatboy changed the ignition switch and problem was solved Have a 97 FXDWG. Installed a badlander load equalizer 17 years ago for run and brake lights on the rear. If the bike is not moving the right turn signal functions correctly.
Why does my bike turn signal not flash?
If the bike is not moving the right turn signal functions correctly. If bike is moving, if you press the right turn signal, it will light up, but not flash. Looked in the service manual and this problem is not listed for troubleshooting the turn signals. Any suggestions? Hi, Mike. Would try the signal function without the Badlands module.
Why are the turn signals on my hog not flashing?
Find the orange wire that feeds 12 volts to your turn signal module. Power it off of a breaker that is powered on, both 1 & 2 “clicks”. My speedometer is working erratic. When I give it throttle the speedimeter digital reading goes blank and the engine light comes on and the turn signals will not flash. When I come to a stop they work
Why does my badlander turn signal not flash?
Installed a badlander load equalizer 17 years ago for run and brake lights on the rear. If the bike is not moving the right turn signal functions correctly. If bike is moving, if you press the right turn signal, it will light up, but not flash. Looked in the service manual and this problem is not listed for troubleshooting the turn signals.
What to do if your speedometer is not working?
Speedometer not working… Speedometer lights up and does everything else but move the needle off of zero. I checked the connection under the instrument console, ran a diagnostic to find out that all codes are clear.
Why is the ABS light and brake light not working?
I have a 1998 Dodge Ram 1500 Both the ABS light and the brake light are on. Changed the Speed sensor on the differential it didn’t help. I did replace the RWAL/ABS fuse and now the speedo works. Next I’m checking the front wheel sensors after that idk what to try. Any advise would be helpful. I have a 99′ Dodge RAM 2500.
Is it time for a new speed sensor?
Perhaps it is time for a new speed sensor? or is it time for a new speedo. 2000 softail deuce. Okay. I replaced the speed sensor ($58) from the dealer.
Why is the odometer on my Harley Davidson not working?
The odometer mileage is displayed but does not change. The trip meter stays the same and does not change. The directionals don’t self cancel any more. All codes clear. I recently installed an amp with speakers that runs off of an ipod.
Where does the flasher go on a Harley Davidson?
Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad.
Why does my LED flasher Blink so fast?
Hyperflashing is when the turn signals blink faster than your stock incandescent bulbs did. This happens because your new LED bulbs draw such little power that your turn signal relay sees the bulbs as being out. Installing an LED flasher module specifically designed for LED bulbs.
Had the same problem on a 99 Fatboy changed the ignition switch and problem was solved Have a 97 FXDWG. Installed a badlander load equalizer 17 years ago for run and brake lights on the rear. If the bike is not moving the right turn signal functions correctly.
Why are my turn signal lights not flashing?
My Harley Heritage Softail 1996 indicator/turn signal lights stay on when instead of blinking. I hit the “turn” button for the signal/turn lights, but they just come on and stay on!
Installed a badlander load equalizer 17 years ago for run and brake lights on the rear. If the bike is not moving the right turn signal functions correctly. If bike is moving, if you press the right turn signal, it will light up, but not flash. Looked in the service manual and this problem is not listed for troubleshooting the turn signals.
How does the turn signal on a Harley Davidson work?
The Turn Signal Security Module monitors the signals and the alarm system for the bike. When there is a problem, the red light key will illuminate. Diagnosing and clearing the codes on each module is really simple, as explained below.
Why is my turn signal on on my Dyna Glide?
Diagnosing and clearing the codes on each module is really simple, as explained below. Before resetting the Turn Signal Security Module, you should check some of the basic reasons as to why the red light is turned on. These reasons include a dying key fob battery, blown turn signal bulb, or bad fuse.
How do you turn off lights on a bike?
This method should work with all bikes built after 2001. Move kill switch to off position, turn ignition on-off-on-off-on. Press left turn signal switch twice, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash twice.
Do these parts fit your Harley Davidson Fatboy?
Do these parts fit your vehicle? Find out now. 2003 Harley Dyna Spedometer Housing Dash Indicator Lights Wiring *VIDEO!! (Fits: Harley-Davidson Fatboy)
If the bike is not moving the right turn signal functions correctly. If bike is moving, if you press the right turn signal, it will light up, but not flash. Looked in the service manual and this problem is not listed for troubleshooting the turn signals. Any suggestions? Hi, Mike. Would try the signal function without the Badlands module.
Find the orange wire that feeds 12 volts to your turn signal module. Power it off of a breaker that is powered on, both 1 & 2 “clicks”. My speedometer is working erratic. When I give it throttle the speedimeter digital reading goes blank and the engine light comes on and the turn signals will not flash. When I come to a stop they work
Can a broken turn signal on a Harley Davidson be fixed?
This article applies to the Harley Davidson Touring. A busted or erratic turn signal repair can be a drag to fix, especially on the road. It’s not a showstopper because you can still ride. But turn signals are an essential part of bike safety. Hand signals are fine during the day, yet are hard to see at night.
Why does my Harley Davidson have no power?
Last Friday I shut the motor off with the stop switch and then turned the ignition key off. I re-set the stop switch to On. 1 minute later, I turned the ignition switch to ignition and noticed I had no power to my headlights and instrument lights.
What are the symptoms of a failing body control module?
5 Common Symptoms of a Failing Body Control Module (BCM) You are here: The Body Control Module (BCM) could be considered a central organizational module for your vehicle. It streamlines the manufacturing and troubleshooting aspects of electronic modules by housing the modules into one, central unit instead of each function having its own device.
What are the turnsignals on a Harley Davidson?
1) Turnsignals all stock means the front signal lights one of the two filaments in the front; the rear signal lights use single filiament lights.
How do you reset the turn signal on a Harley Davidson?
Press left turn signal switch twice, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash twice. Press right turn signal switch once, pause, and lights will flash three times.
Why is my left turn signal light not flashing?
Operate the switch to turn the left turn signal light. Back probe the wire that supplies power to the switch; the test light should flash. If the test light doesn’t flash, there is a problem with the flasher unit or an open or short between the switch and the battery power source.
Press left turn signal switch twice, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash twice. Press right turn signal switch once, pause, and lights will flash three times.
How do you reset the turn signal on a Dyna Glide?
Press left turn signal switch once, and light will flash a number of times to indicate an error code. There is 1.5 seconds between flashes to indicate 1st and 2nd digit of codes and four second pause between codes. Press and hold left switch down for five seconds, and light will flash twice to indicate the TSSM is reset. Turn ignition to off.
What kind of turn signal does a Harley Fat Boy use?
Fits: 1990-2017 Harley Fat Boy (FLSTF) Custom way to replace stock turn signals Bolt directly to stock mounting holes with no drilling Super-bright, single-function amber… Black low Profile LED Marker lights from Alloy Art are designed to fit older model Softail fender struts.
What to do if left turn signal is not working?
If you don’t have a manual, then have a look at the TS module and hopefully the pins are labled. If you apply 12 vdc to the (Lt out) pin -the Left turn signal lights should come on. (you’ve just bypassed the TSM) Next.. connect a jumper from (Lt in)pin to (Lt out) pin & press the Left turn signal switch.
Why are my turn signals not flashing on my Harley Davidson?
If you are stuck with having to manually cancel the turn signals, the problem could be found in connectivity to the speedometer or the TSSM. Check the switches. Check for loose or disconnected wires to the speedometer. Check the tip switch that cancels if the bike falls over.
Why does my turn signal on my Dyna not flash?
I have a ’94 dyna wide glide and whenever I use the turn signals they do not flash, if I hit the right signal it just lights up soild and does not flash and that goes for the left side as well. I went to the dealer and asked what would cause this problem my first guess was a relay but the dealer said it was most likely the turn signal module.
If you don’t have a manual, then have a look at the TS module and hopefully the pins are labled. If you apply 12 vdc to the (Lt out) pin -the Left turn signal lights should come on. (you’ve just bypassed the TSM) Next.. connect a jumper from (Lt in)pin to (Lt out) pin & press the Left turn signal switch.
How can I tell if my turn signal module is faulty?
You can pretty much determine if the module is faulty by following the troubleshooting steps outlined in the manual. If you don’t have a manual, then have a look at the TS module and hopefully the pins are labled.
How does the turn signal work on a Harley Davidson?
Timing for turn signals is picked up by the speed sensor to control the time out distance/time. The speed sensor feeds the speedometer through the TSSM and also the ECM for controlling fuel flow to the injectors. If you need to reset your TSSM security module, refer to Step 5 for instructions.
Is there a tail light assembly for a Harley Davidson?
Only 5 left in stock – order soon. . . Chromed Tail Light Assembly. Replaces Harley Davidson 68008-73A Big Twin 1973 + . . . Only 5 left in stock – order soon. . . . . Only 15 left in stock – order soon.
How big are the lights on a Harley Davidson Road Glide?
3-1/4 Inch LED Turn Signal Kit Flat Smoke Lens 1157 Double Base Amber Front Turn Signal Bulbs + 1156 Single Connector Red Rear Turn Signal Lights Compatible with Harley Motorcycle Road Glide Road King . . . Only 11 left in stock – order soon. . Only 6 left in stock – order soon.
Why are the turn signals on my Harley Davidson not working?
I’m not getting any power to the right side turn signals, the green arrow on the dash don’t light up on right, and turn signals are very dim and slow on left side. Wiring seems to check out, fuses ok.
You can pretty much determine if the module is faulty by following the troubleshooting steps outlined in the manual. If you don’t have a manual, then have a look at the TS module and hopefully the pins are labled.
Why does my Harley Davidson bike not start?
If you can start the bike this way; the start switch is probably bad, or a wire may be damaged. Let us know what you find. Sounds like you know what you are doing. You are not going to believe this – but – it was the battery in the key fob. The bike has to have a signal from the key fob before it will allow the bike to start.
Why does my rear turn signal not flash?
Rear signals are still hooked up but don’t flash.. yes, bsmith. most likely they don’t work because they aren’t hooked up , up front. ypu can wire a resistor inline to remedy that. yes, bsmith. most likely they don’t work because they aren’t hooked up , up front. ypu can wire a resistor inline to remedy that.
Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad.
Why is my hazard light not working on my Harley?
Check the hazard light box and make sure all signal wires are attached. Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad. If only one light (or one side) isn’t working, check the power to the bulb plug-in connections.
Why is my turn signal on my Harley Davidson not flashing?
A cheap easy fix ! could be wrong but i belive this can alos be caused from bad connection or problem with wireing to signal itself. after i wired my rear fender my left signal stopped flashing. investigated and a clip broke loose under my fender and wiring for left side was hitting on the tire. wire got a little chewed up. replaced it. good to go.
What does it mean when your turn signal does not flash?
Have a 97 FXDWG. Installed a badlander load equalizer 17 years ago for run and brake lights on the rear. If the bike is not moving the right turn signal functions correctly. If bike is moving, if you press the right turn signal, it will light up, but not flash.
Why is my left turn signal not flashing?
When it’s not working, there is no signal front & rear and no signal indicator either. When working, both markers function properly as does the indicator. With new bulbs installed and sockets cleaned, I’ve narrowed the problem down to either the left turn signal switch or the turn signal module.
Why is my turn signal not working on my Harley?
You may have a bad module or corroded/bad connections at the module or at the handlebar switch harness/ plug. If you determine that you need a turn signal module, we suggest Badlands. I have 2005 Road king Classic, the alarm light is coming while riding and the fob is not being touched to arm or disarm the alarm.
Do these parts fit your vehicle? Find out now. 2003 Harley Dyna Spedometer Housing Dash Indicator Lights Wiring *VIDEO!! (Fits: Harley-Davidson Fatboy)
Where is the bank angle sensor on a Harley Davidson?
On some bikes it’s called a Bank Angle Sensor (BAS) and is located in the Turn Signal Security Module (TSM or TSSM). Check and clean your speed sensor. It may seem irrelevant but the TSSM serves many functions. Timing for turn signals is picked up by the speed sensor to control the time out distance/time.
What does diag stand for on Harley Davidson Softail?
Press and hold the black odometer reset button and turn the ignition switch to the ignition position. Hold the reset button until the message “DIAG” appears. Press and release the odometer button to access the module selection menu. The message “P55PtB” will appear. The letters and numbers stand for the different systems.
On some bikes it’s called a Bank Angle Sensor (BAS) and is located in the Turn Signal Security Module (TSM or TSSM). Check and clean your speed sensor. It may seem irrelevant but the TSSM serves many functions. Timing for turn signals is picked up by the speed sensor to control the time out distance/time.
Press and hold the black odometer reset button and turn the ignition switch to the ignition position. Hold the reset button until the message “DIAG” appears. Press and release the odometer button to access the module selection menu. The message “P55PtB” will appear. The letters and numbers stand for the different systems.
What should my Electrical reading be on my Softail?
A normal reading is around 100 amps. If your reading is higher, you may have mechanical engine damage, a faulty starter, or high resistance in the wiring routed between your starter and battery. The wiring can be checked fairly quickly. Place your multimeter’s negative lead on the starter ground wire and the positive lead on battery negative.