Why is the starter not turning on my Pontiac Grand Am?
If you can hear the starter motor turning but the engine isn’t turning (look at the belt) then the starter may not be engaging (in your car I believe this means that you must replace the whole starter). You can remove and test your starter to confirm whether or not the solenoid is engaging the starter.
Why does my car engine not want to start?
If the engine still doesn’t seem like it wants to start, probably fuel is getting into the cylinders and your problems lies somewhere else. However, if the engine runs momentarily and dies, then the problem is that fuel is not getting to the cylinders. Check for a clogged fuel filter, or a bad fuel pressure regulator.
Why does my GM car say no start no crank?
How to diagnose a no start no click on GM vehicle. If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that.
What to do if your starter isn’t turning?
If this doesn’t solve the problem, make sure that the engine is actually turning when you attempt to start it. If you can hear the starter motor turning but the engine isn’t turning (look at the belt) then the starter may not be engaging (in your car I believe this means that you must replace the whole starter).
If you can hear the starter motor turning but the engine isn’t turning (look at the belt) then the starter may not be engaging (in your car I believe this means that you must replace the whole starter). You can remove and test your starter to confirm whether or not the solenoid is engaging the starter.
How to diagnose a no start no click on GM vehicle. If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that.
What causes a GMC truck to turn over but not start?
If the engine starts up normally after doing that, it means that fuel pressure is bleeding off and the fuel pump needs to prime the lines before it can start. It can bleed off from one of two places. 1. Fuel pressure regulator has an internal leak, and fuel is bleeding off back to the tank though the return line. 2.
What causes a jeep to have a no start condition?
The usual suspects, that can cause this type of problem, are a bad fuel pump, bad crank sensor, bad ignition coil (if your Jeep is distributor equipped), etc. Does Not Crank Condition: Means that the engine is not cranking when you turn the key to crank the engine.
What causes a car to not start after running out of gas?
Therefore most knock sensor faults or issues should have little to no effect on the operation of the… If the engine was sputtering and then when the exhaust starts to come off it makes the engine run better, then there is either a plugged muffler or a plugged catalytic converter.
Why does my Car Crank and not start?
There are many reasons for your car to crank and not start. Anything from factory security system locking you out, bad fuse/relay, clogged fuel filter,faulty fuel pump, oil sending unit/crank sensor failure, clogged catalytic converter, failing electronic ignition, ECM/PCM,etc.,etc.
Why is my fuel pump reset button not working?
Anything from factory security system locking you out, bad fuse/relay, clogged fuel filter,faulty fuel pump, oil sending unit/crank sensor failure, clogged catalytic converter, failing electronic ignition, ECM/PCM,etc.,etc. As a first step best to see if there are any stored trouble codes that could point directly to the fault.
There are many reasons for your car to crank and not start. Anything from factory security system locking you out, bad fuse/relay, clogged fuel filter,faulty fuel pump, oil sending unit/crank sensor failure, clogged catalytic converter, failing electronic ignition, ECM/PCM,etc.,etc.
Anything from factory security system locking you out, bad fuse/relay, clogged fuel filter,faulty fuel pump, oil sending unit/crank sensor failure, clogged catalytic converter, failing electronic ignition, ECM/PCM,etc.,etc. As a first step best to see if there are any stored trouble codes that could point directly to the fault.
What kind of car is the Pontiac Grand Am?
The Pontiac Grand Am is a mid-size size (and later compact) car produced by Pontiac. The 1999-2005 generation is the final generation of the Pontiac Grand Am. 2003 Grand Am will not start.
Where is the fuel pump on a Pontiac Grand Am?
Check in the engine compartment fuse box, it should be near the battery under the hood. The cover should be pretty easy to remove. The fuel pump should be connected through a fuse in slot 48. If that fuse looks good, then you may want to check the fuel pump relay (also inside the engine compartment fuse box).
What to do if your crankshaft sensor is not working?
Issues with the crankshaft sensor can quickly lead to problems that affect the drivability of the vehicle. For this reason, if you suspect your crankshaft position sensor has an issue, have the vehicle inspected by a professional technician right away. They will be able to diagnose your car and replace your crankshaft position sensor if necessary.
How do you test a car relay with no power?
If there is no power, the electrical system must be tested starting with the fuse then the relay. If power is present use the test light connected to battery power to check the ground circuit. if these tests check out, the accessory is bad and needs to be replaced.
Where is the fuel pump relay on a Pontiac Grand Am?
The fuel pump relay is #18 in the fuse box. Start with the car off, and have somebody else put the key in the cars ignition and attempt to start the car while you listen to the relay. If you can hear this relay make a “clicking” noise as the car attempts to start, then it is working properly.
Why does my GM car not start after I remove the radio?
Because again, GM’s starter is radio based and the fact that you removed the original radio that was in the car. Revived a 4 year old thread…I can imagine the Pontiac isn’t around anymore.
Why does my 2003 Grand Am Not Start?
My 2003 Grand Am sometimes wont start. I’ve noticed that when it wont start, the security light is flashing. To resolve the problem I have to leave the key in the ignition with it in the “ON” position for 12 minutes to reset the sensor. The sensor light wiull stop flashing when it is reset.
How much does it cost to fix a no start Pontiac Grand Am?
Our technicians tell us that the ignition lock cylinder should be replace to correct this condition. The average cost for a Pontiac Grand Am No Start Diagnosis is between $88 -$111. Learn More Good news! We found 32 RepairPal Certified shops near you.
How to fix a Pontiac Grand Am PassLock sensor?
Best way to fix is to permanently disable/disconnect passlock system. Not fixed, security light comes on solid and goes away in different time intervals while driving, then after a couple of starts it goes in that limp mode where the security light blinks. I continuously have to wait until the light stops blinking….
What to do if your car won’t start?
Only when the security system is enabled, security light off, the car has starting issues. Best way to fix is to permanently disable/disconnect passlock system. Not fixed, security light comes on solid and goes away in different time intervals while driving, then after a couple of starts it goes in that limp mode where the security light blinks.
Why does my GM 3.1L engine not start?
When a malfunction occurs in one of the components that make up the anti-theft system (usually the lock cylinder), the PCM disables the fuel injectors after the engine has started, causing the engine to stall after about 3 seconds of run time. PASS-Key/Passlock system failures are a very, very common cause of no start conditions.
Why is my Pontiac G5 engine not starting?
There are a lot of issues that can cause your G5 to crank, but not start. The engine needs air, fuel, and a spark in order to run. It is highly likely that if the engine is cranking, but not starting that it has thrown an OBDII code. It is definitely worth it to use an OBDII scanner to check and see if the engine has thrown any trouble codes.
Why does my Pontiac Grand Am Not Start?
I have been in the auto industry for more than 20 years and would like to share my knowledge with others. Due to how many vehicles I buy, sell, and repair I will be uploading new videos as I come across common and uncommon problems and simple maintenance. An error occurred while retrieving sharing information.
What does it mean when your G6 won’t start?
There are really two main ways that a vehicle will not start. The first and most common is when it won’t turn over. This just means that the engine doesn’t move when you turn the key. The second way that your G6 won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own.
How to troubleshoot a GM 3.1L no start?
Important Tips And Suggestions. No Start Condition Basics. No Start 1: Checking For Spark. No Start 2: Checking For Fuel. No Start 3: Anti-Theft System Checks. No Start 4: Checking Engine Mechanical Condition. No Start Summary. Related Test Articles.
The fuel pump relay is #18 in the fuse box. Start with the car off, and have somebody else put the key in the cars ignition and attempt to start the car while you listen to the relay. If you can hear this relay make a “clicking” noise as the car attempts to start, then it is working properly.
The Pontiac Grand Am is a mid-size size (and later compact) car produced by Pontiac. The 1999-2005 generation is the final generation of the Pontiac Grand Am. 2003 Grand Am will not start.
If this doesn’t solve the problem, make sure that the engine is actually turning when you attempt to start it. If you can hear the starter motor turning but the engine isn’t turning (look at the belt) then the starter may not be engaging (in your car I believe this means that you must replace the whole starter).
What to do if your car wont start after replacing the fuel pump?
Car won’t start even after I replaced the fuel pump. Car won’t start and turned off while driving. Replaced the fuel pump and I can hear it working. The car still won’t start.
Why does my car not start when stopped at a gas station?
It seems to happen more when I am stopped at a gas station, (not getting gas)- as crazy as that sounds. When it won’t restart, it will turn over and crank and act like it’s not getting fuel. We have checked the coils, fuel pressure regulator and just now replaced the fuel pump.
When did my car have a no start problem?
I have had a no start problem about 3 times. The first time this happened was in January of last year. Came out to start my car and it would not start. Prior to this incedent the car started fine since I had it. My friend came over and ran test on the cars computer. Came out it was the fuel pump. So i had him replace the fuel pump.
Why does my Pontiac Grand Prix not start?
26 people found this helpful. When your car starts fine cold, then fails to restart while warm, it is usually a coolant system problem. Either low coolant, or bad coolant level sensor. 26 people found this helpful.
What causes no start on a GM 3.1L?
I’m going to show you two different methods to verify if the no start condition on your 3.1L or 3.4L GM vehicle is due to a lack of fuel, which usually means that the fuel pump has gone bad. One method involves using just starting fluid and the other involves using a fuel pressure gauge.
What does 0 psi mean on fuel pump?
CASE 1: If the fuel pressure gauge registered 0 PSI. This confirms that the cause of your Venture’s (Malibu, Impala, Lumina, Grand Am, Cutlass Supreme, etc.) is caused by a lack of fuel.
Check in the engine compartment fuse box, it should be near the battery under the hood. The cover should be pretty easy to remove. The fuel pump should be connected through a fuse in slot 48. If that fuse looks good, then you may want to check the fuel pump relay (also inside the engine compartment fuse box).
The fuel pressure gauge will register 0 PSI. OK, let’s analyze your test results: CASE 1: If the fuel pressure gauge registered 0 PSI. This confirms that the cause of your 3.8L equipped GM car or mini-van is caused by a lack of fuel.
Important Tips And Suggestions. No Start Condition Basics. No Start 1: Checking For Spark. No Start 2: Checking For Fuel. No Start 3: Anti-Theft System Checks. No Start 4: Checking Engine Mechanical Condition. No Start Summary. Related Test Articles.
How to test the alternator ( GM 3.1L )?
How To Test The Alternator (GM 3.1L, 3.4L). One of the most important pieces of info you need to know, about what makes the engine in your car start and run, is that it needs 3 specific things when it’s cranking. These three things are: Air. Fuel. Spark. When one of the above is missing, the engine in your car or mini-van cranks but does not start.
Can a GM 3.1L mini van not start?
Your GM 3.1L, 3.4L equipped car or mini-van is a complicated machine but, not impossible to diagnose/troubleshoot it when it doesn’t want to start and run. The key to saving yourself time and money, when troubleshooting a cranks but does not start condition, is to check the basics first.
When a malfunction occurs in one of the components that make up the anti-theft system (usually the lock cylinder), the PCM disables the fuel injectors after the engine has started, causing the engine to stall after about 3 seconds of run time. PASS-Key/Passlock system failures are a very, very common cause of no start conditions.
How To Test The Alternator (GM 3.1L, 3.4L). One of the most important pieces of info you need to know, about what makes the engine in your car start and run, is that it needs 3 specific things when it’s cranking. These three things are: Air. Fuel. Spark. When one of the above is missing, the engine in your car or mini-van cranks but does not start.
Why is my air conditioning not working in my Pontiac Grand Am?
If the controls feel fine, but have no effect on the air then it is probably a blown fuse. If you cannot hear the accompanying blowing sound when the air is turned from low to high, then the problem is in the blower motor. Disconnect the black negative battery cable first when looking for the blower motor.
When did the Pontiac Grand Am 5th generation come out?
In this article, we consider the fifth-generation Pontiac Grand Am, produced from 1999 to 2005. Here you will find fuse box diagrams of Pontiac Grand Am 1999, 2000, 2001, 2002, 2003, 2004 and 2005, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
What to do if your car won’t start after getting gas?
To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information. Please try again later. Good Vibrations? – Steering Wheel Shakes
What causes the fuel pump to not start?
The fuel pump is running and delivering normal pressure to the engine But, with all that working your engine still will not start. So, the most likely cause, is that the fuel injectors are probably not opening. The (PCM) uses the trigger signal from the crankshaft position sensor; and/or camshaft position sensor to pulse the injectors.
The fuel pump is running and delivering normal pressure to the engine But, with all that working your engine still will not start. So, the most likely cause, is that the fuel injectors are probably not opening. The (PCM) uses the trigger signal from the crankshaft position sensor; and/or camshaft position sensor to pulse the injectors.
What causes a car to start and then die?
But if there is a fuel leak somewhere, then the proper amount of fuel won’t be able to make it to the combustion chamber. This might cause the engine to still start, but it won’t be able to keep it running. That is why it will die almost immediately after it starts.
https://www.youtube.com/watch?v=kPnSa06tvqQ
What causes a car engine to not start?
All engines require three things to start and run: spark, fuel and compression. If any one of these is missing, your engine will not start. But with all that working your engine will not start. Engine Will Not Start-The most likely cause is that the fuel injectors are probably not opening.
Why does my pontaic Grand Am Se not start?
HI I HAVE A 2OOO PONTAIC GRAND AM SE TURNS OVER FINE NO START…IT SEEMS AS SOON… AS U TURN IGNITION TO ON IT BLOWS THE 10 AMP FUSE IN FUSE BOX UNDER HOOD…IT SAYS PCM IGNITION HELP SCOTT
How much does a Pontiac Grand Am cost?
The average cost for a Pontiac Grand Am General Diagnosis is between $88 -$111. Learn More Good news! We found 32 RepairPal Certified shops near you. Here’s a few you can book directly with.
What causes a car to go ” no start “?
Pass lock light not lit. All 5 ignition fuses are good. Assuming ignition lock cylinder needs to be replaced Good car . This issue just happens. Steering wheel locked and wont release to start the car . Key wont turn . HI I HAVE A 2OOO PONTAIC GRAND AM SE TURNS OVER FINE NO START…IT SEEMS AS SOON…
Why does my Pontiac Grand Am keep overheating?
I gotta 1999 pontiac grand am se 3.4 it ran ok when I first got it then seripeteen belt broke overheated a lil had problems since.got belt fixed then had problems with the fans not wrking also so hooked them up direct an found out outta 2 fans one wrked.
The Pontiac Grand Am is a mid-size size (and later compact) car produced by Pontiac. The 1999-2005 generation is the final generation of the Pontiac Grand Am. Why dose my car keep overheating?
Why is my GM 3.1L engine not cranking?
A no crank condition means that the engine is not cranking when you turn the key to crank the engine. This is usually due to a bad starter motor, bad ignition switch, bad neutral safety switch, or maybe the engine threw a rod and is locked up.
Where are the fuse blocks on a Pontiac Grand Am?
There are two fuse blocks, which are located on the right and left in the dashboard, behind the covers. How to check the fuses? How to replace a blown fuse? Why do car fuses blow?
What to do when your Pontiac Grand Am won’t start?
To resolve the problem I have to leave the key in the ignition with it in the “ON” position for 12 minutes to reset the sensor. The sensor light wiull stop flashing when it is reset. Then I turn the key off and then back to start. It works every time but the 12 minute wait is a pain in the ass.
Can a Pontiac Grand Am run at high idle?
When the cooling fans turn on at 223 like there supposed to if you keep your foot in it sitting still for another Minuit at 2500 rpm it will take over by itself and run idle up to about 3500 by itself. If you turn off and restart it is fine until it gets back up in temp. Had a GM tech look at it in 35 years hes never seen one do this.
How to troubleshoot a no start Chrysler 2.0L?
Go to: No Start 2: Checking Fuel. CASE 2: Spark was NOT present in all of the cylinders This usually tells you that the ignition coil pack is bad (or missing power) or the crank sensor is bad. It’s usually one or the other, I have never seen both go out at the same time.
Why is there no pressure on the fuel rail?
If the pressure at the exit side of the fuel filter is normal and yet the pressure on the fuel rail is essentially zero, it’s possible the fuel pressure regulator has failed wide open, essentially preventing sufficient pressure from building.
Can a failed fuel pump cause a failed pressure regulator?
[&hesitation&]. However, other worn out or failed components—like the [&fuel&] filter, fuel pump, and automatic transmission issues—can also [&cause&] similar symptoms to those of a [&failed&] [&pressure&] [®ulator&]. So you need a way to troubleshoot the [®ulator&] in your vehicle whenever you suspect a malfunction.
What are symptoms of no start and no fuel pressure?
It may also effect 4.6 and 5.4 vehicles but I kinda doubt it. Symptoms are a no start and no fuel pressure at the fuel rail. Fuel relay tests good but not receiving switched input signal from PCM. Fuse 24 (30amp MAXI fuse) is blown for PCM. Loading…
How to test the fuel pump no start?
These are the test steps: Connect the fuel pressure gauge to the Schrader valve on the fuel rail. When ready, ask your helper to crank the engine while you observe the fuel pressure tester’s gauge. 1.) The fuel pressure gauge will register 35 PSI, or 2.) The fuel pressure gauge will register 0 PSI.
I’m going to show you two different methods to verify if the no start condition on your 3.1L or 3.4L GM vehicle is due to a lack of fuel, which usually means that the fuel pump has gone bad. One method involves using just starting fluid and the other involves using a fuel pressure gauge.