When did Mercedes start using on board diagnostics?
Back in the day when Mercedes first ventured into the world of on board diagnostics in the era of the 1984’s W124 and its stable mates they began to introduce electronic code diagnostics. The first being either through an 8 pin (X92) or 16 pin (X11/4) square block fastened to the bulkhead.
What kind of communication system does a Mercedes Benz use?
Without going into too much detail this new system used ISO9141 communication protocol to access the vehicle electronics via a common communications module. This used both a K-line and L-line connection and Mercedes own communications language to access the system.
How do you level a Mercedes Benz W124?
Brace the back of the bolt on the adjustment arm with an 8mm wrench and use a 10mm wrench to remove the Nylex nut (red arrow). Leave the arm attached to the sway bar bracket. There is an adjustments on the arm to set the level position once the car is back on the ground (red arrow).
How to bleed a Mercedes Benz hydraulic system?
Installation is the reverse of removal. You will need to use the adjusting arm to set the level arm (red arrow) at the right height. You can bleed the system using the bleed valve on the top (yellow arrow). The procedure for bleeding is the same as bleeding the brakes or hydraulic clutch.
When did the Mercedes W110 chassis come out?
Our primary focus is providing solutions to the most common technical problems that owners face on the early 1960’s up through the early 2000’s. These include the W110 W111 W113 W108 W109 W114 W115 R107 W116 W123 W126 W201 W124 R129 W140 W210 W211 and W220 chassis.
Is there a way to repair your Mercedes?
MercedesSource.com | Let us repair it yourself. Kits, Tools, and Tips for fixing your Mercedes. Sometimes you find one that has that special “feel.” Meet Bubbles
How old are the engines on a Mercedes?
I personally consider this man one of the best automotive designers of all time. He shaped the face of Mercedes Cars during the 1980s and 1990s. Don’t think yours is ok. Get under the rear and visually inspect it. The M116 and M117 V8’s survived production for over 20 years (1970 to 1991), so now these engines are all 30 to 50 years old.
How did the Mercedes W123 bubble get its name?
This is a very special 300D turbo diesel sedan. It was named “Bubbles” by the previous owner because she felt the color looked like the color of champagne. Rather than try to tell you all about this car, I am going to have you watch a number of videos below. The first video will explain how we came to be owners of this pretty W123.
Where are the diagnostic pins on a Mercedes?
This was commonly located within the ECU box and was accesses by removing a sealed access cap. Although 38 pins were used only the pins relating to build options were loaded and as such gave diagnostic flash / blink access to the cars individual modules.
When did Mercedes stop using blink and flash diagnostics?
Mercedes were in parallel developing their own digital diagnostic system and not following the industry standard of OBD1/2. From August 1995 production date Mercedes phased out the analogue type of flash/blink diagnostics in favour of their propriety digital code reading system.
What is the Diagnostic fault code for Mercedes Benz?
Mercedes older series diagnostic fault code reading. W124.R129 1980’s – 1990’s era As you are reading this you will probably be wishing to extract a fault code or clear a fault indicator lamp from the dashboard of your older Mercedes Benz model vehicle.
What does it mean when your turn signal is not working on Mercedes?
In newer Mercedes models, you will get a warning on instrument cluster stating “Turn Signal Left / Right / Front / Rear / Side Malfunction”. Depending on the Mercedes model and problem a warning may or may not show on the dashboard.
Are there any problems with the Mercedes engine?
Theses engines were more powerful and more fuel efficient. They did have a few teething problems but have proven to be very durable as long as they are treated and maintained properly. A true challenge – but you can do it with the right knowledge.
How can I fix a problem with my Mercedes?
If you have a problem with your older Mercedes and are trying to figure what is causing it or how to fix it, you have come to the right place. Let Kent explain how his solutions finder works: “Just select the location of the problem you are experiencing, the chassis designation of your car and a few key words and click Search.
When did Mercedes Benz stop using cast iron?
We know that most owners can live with some looseness in the suspension, especially when you consider the age of the 123 chassis. Produced from 1984 to 1993 these lighter weight aluminum head engines replaced the venerable cast iron 616 and 617 engines of the 1970’s and early 1980’s.