What is the fault code for Mercedes C class?
Common fault codes: P1856 – Selector Lever Position Detection Failed; P240C – CAN Signal Selector Lever Position N15/5 Is Not Plausible Affected Vehicles: Mercedes A-Class 2004 – 2012 (W169) Mercedes C-Class 2005 – 2009 (W203 and pre-facelift W204) Mercedes CLK 2005 – 2009 (C209/A209) Mercedes CLS 2005 – 2009 (W219)
What are the diagnostic codes for Mercedes Benz?
Mercedes-Benz Diagnostic Trouble Codes (DTC) for 1996+ models Powertrain P0100 Mass or Volume Air Flow Circuit Malfunction P0101 Mass or Volume Air Flow Circuit Range/Performance Problem P0102 Mass or Volume Air Flow Circuit Low Input P0103 Mass or Volume Air Flow Circuit High Input P0104 Mass or Volume Air Flow Circuit Intermittent
What’s the fault code on a Mercedes 190E?
It’s W201 190E, with M111 engine (2.2Lt.) from E220, W124. There is no major symptom, just very little rough idle. I made the DIY code reader and check it, then found those codes. What I confused is…which “set”of codes I should refer to…
How many control units does a Mercedes Benz have?
There are also codes for other control units such as transmission, ABS, SRS, ESP, 4ETS, airbag, A/C. Mercedes-Benz can have up to 47 control units. You can NOT diagnose them with a simple OBD-2 scanner. To read these systems and their fault codes or erase them from your Mercedes-Benz you need more advanced OBD-II scanners.
Can you erase a fault code on a Mercedes Benz?
Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS This is diagnostic scanner used at Mercedes-Benz dealerships.
What does Mercedes Fault code p0400 mean?
P0400 Mercedes Fault Codes Meaning Mercedes Fault Code Fault Code Meaning P0466 Purge Flow Sensor Circuit Range/Performa P0467 Purge Flow Sensor Circuit Low Input P0468 Purge Flow Sensor Circuit High Input P0469 Purge Flow Sensor Circuit Intermittent
What are all the codes on a Mercedes Benz?
Use an advanced OBD-II code reader to read and erase Engine CEL, Transmission, ETS, ABS, Airbag and other systems. There are also codes for other control units such as transmission, ABS, SRS, ESP, 4ETS, airbag, A/C. Mercedes-Benz can have up to 47 control units. You can NOT diagnose them with a simple OBD-2 scanner.
Where is the p0172 fault code stored in a Mercedes Benz?
P0172 Mercedes-benz Description. This fault code is stored in the Engine Control Module (ECM) when the ECM is no longer capable of controlling the air fuel ratio. For correct operation of the catalytic converter the ECM is required to keep the air fuel ratio (AFR) at approximately lambda 1, this equates to an AFR of 14.7:1 by mass.
Are there any problems with Mercedes Benz COMAND system?
We have listed down common issues with the Mercedes-Benz COMAND system, including problems with The most common solution to fix any of these issues is to try to perform a soft reset of the COMAND unit.
Is there an OBD-2 scanner for Mercedes Benz?
You can NOT diagnose them with a simple OBD-2 scanner. To read these systems and their fault codes or erase them from your Mercedes-Benz you need more advanced OBD-II scanners. Top 3 OBD-2 code readers for Mercedes-Benz have been listed under the green column below. 1. OBD II Code Reading Scanners – For ECU Only 2.
Can a launch creader VIII read a fault code?
1. Launch Creader VIII Can read fault codes from multiple systems such as transmission, engine, ETS, airbag and more. Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3.
Can you read the fault code on a Mercedes Benz?
Can read fault codes from multiple systems such as transmission, engine, ETS, airbag and more. Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS
It’s W201 190E, with M111 engine (2.2Lt.) from E220, W124. There is no major symptom, just very little rough idle. I made the DIY code reader and check it, then found those codes. What I confused is…which “set”of codes I should refer to…
You can NOT diagnose them with a simple OBD-2 scanner. To read these systems and their fault codes or erase them from your Mercedes-Benz you need more advanced OBD-II scanners. Top 3 OBD-2 code readers for Mercedes-Benz have been listed under the green column below. 1. OBD II Code Reading Scanners – For ECU Only 2.
1. Launch Creader VIII Can read fault codes from multiple systems such as transmission, engine, ETS, airbag and more. Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3.