How to replace Silverado evaporator without removing dashboard?
Silverado Evaporator Replacement Trick (Replace Without Removing Dashboard!) – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.
Where to remove the evaporator from a car?
This operation should be performed by a licensed refrigerant handler. Remove the liquid line connection that goes to the evaporator, and then remove the heater hoses from the core. Next, remove the air conditioning and heating unit from under the dashboard, which is located under the instrument panel.
How do you replace an air conditioner evaporator?
Flip the unit back over to take the upper half of the “housing” off. Remove the evaporator from the lower housing case. Check for damage to the housing that holds the evaporator for any cracking or wearing, and be sure there are no missing pieces to the housing. Replace any damaged or worn pieces.
How do you replace the evaporator on a Hyundai Elantra?
Once you have the dash out the HVAC box is removed from the vehicle and split in half to replace the EVAP core. Consider replacing the Thermistor or transfer it to the new evap in the exact same location.
How do I remove the dashboard to replace the evaporator on?
Its the article for the removal and replacement of the Evaporator as described in the GM Service Manual: 1. Negative battery cable. 2. Engine coolant. 3. Recover refrigerant. 4. Instrument panel. 5. Electrical connectors, as necessary.
Flip the unit back over to take the upper half of the “housing” off. Remove the evaporator from the lower housing case. Check for damage to the housing that holds the evaporator for any cracking or wearing, and be sure there are no missing pieces to the housing. Replace any damaged or worn pieces.
Once you have the dash out the HVAC box is removed from the vehicle and split in half to replace the EVAP core. Consider replacing the Thermistor or transfer it to the new evap in the exact same location.
This operation should be performed by a licensed refrigerant handler. Remove the liquid line connection that goes to the evaporator, and then remove the heater hoses from the core. Next, remove the air conditioning and heating unit from under the dashboard, which is located under the instrument panel.
Is it OK to drive with EVAP light on?
But because an EVAP leak can potentially be a severe and environmentally damaging problem, it’s not a good idea to keep driving with the check engine light on. Whatever condition your vehicle is in—whether it’s showing symptoms of a fuel leak or not—aim to have the codes pulled as soon as possible.
Why does my car have an EVAP code?
Good news for consumers with vehicles not showing any signs of a fuel leak: even if your check engine light is on and you find an EVAP code via the OBD II reading, it might be a simple fix. In other cases, however, it might not be. The most common reason a vehicle shows an EVAP code is because the gas cap is not secure.
What should I do if I have an EVAP leak?
(Tip) When ordering EVAP replacement parts make sure they match up before installing them also if the dealer has the part “in stock” it usually means there is a high failure rate upon the part. Remove the vacuum control solenoid which is controlled by the computer.
(Tip) When ordering EVAP replacement parts make sure they match up before installing them also if the dealer has the part “in stock” it usually means there is a high failure rate upon the part. Remove the vacuum control solenoid which is controlled by the computer.
How does the EVAP system work in a car?
Your car’s EVAP system is designed to control fuel vapors which are naturally omitted from standing gasoline inside the fuel tank. These vapors are collected into the charcoal canister and then condensed so they can be returned to the fuel tank.
Why is my EVAP line falling off my car?
Next, open the hood and look for the vacuum feed line from the engine intake manifold to the EVAP system control valve. Because of engine heat and vibration it can deteriorate the rubber line causing it to fall off or collapse cutting of the vacuum system to the solenoid.
Can a gas canister leak from the EVAP system?
Since the EVAP system deals with the management of gas and its fumes it can be dangerous when certain malfunctions occur. One such problem can cause the charcoal canister to fill will raw fuel and start to leak which can cause a fire hazard.