Why is the brake light switch on my Mercedes not working?

If you don’t see the letters on the cluster change from P to R to N, it is a good sign that the gear selector module is defective. You can buy a new brake light switch on Amazon for less than $15 USD, just do a search for Mercedes-Benz Brake Light Switches.

Why is the battery on my Mercedes Benz not working?

Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars. How old is the battery on your Mercedes-Benz?

What should I do if my Mercedes Benz won’t start?

Start the car and you should be able to get around 60 psi. When the engine is running and when you turn off the engine the pressure should stay steady. Always perform this test on a cold engine. Next, make sure that the fuel injector connections are secure and not loose. Check the fuel pump and the fuel pump relay.

Why does my Mercedes central gateway not work?

When the Mercedes Central Gateway Module fails, one or more of these systems may stop working. Mercedes Central Gateway Module may fail due to water damage. It can also fail from internal software or hardware defects. Damage to the Mercedes Central Gateway Control module can be caused by a blocked drain valve in the trunk floor.

What happens if a CGW fails on a Mercedes?

A bad CGW can also cause the engine to randomly shut off even when driving. You will have several warning lights stay ON on your cluster, and several features stop working. Below is a list of warning lights and problems you may notice if your Mercedes Central Gateway Control module fails.

Why does my Mercedes zgw control module not work?

Mercedes-Benz Central Gateway Module ZGS (also referred to as CGW) may fail, causing various warning lights or systems to stop working. Mercedes Central Gateway module is the hub that allows communication between various modules. Mercedes ZGW Gateway control module stores data for Mercedes ASSIST or ASSYST plus.

Is the Mercedes-Benz ML350 car does not shift from Park to drive?

Mercedes-Benz ML350 Car does not shift from park to drive Inspection at your home or office. Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM. Our certified mobile mechanics can come to you now. Mercedes-Benz ML350 Car does not shift from park to drive Inspection costs $89 on average.

How to install brake light switch on Mercedes Benz E-class?

Plug the wires in the new switch and install the new switch by twisting it counter-clockwise. Watch the following video on how to install brake stop light switch on an Mercedes-Benz E-Class . I replaced the brake light switch but the lights are still on.

Why is my Mercedes Benz gear shift stuck?

Gear shift stuck is one of the most common problems with Mercedes-Benz cars. Unfortunately, looking to see if the brake lights turns on while you press the brake pad, is not a good test to tell if the brake light switch is working properly.

What to do when your brake lights won’t go off?

Check that the button on switch is aligned with the arm and is being pushed into shut the brake lights off. Pull up on pedal and have some one watch to see if brake lights go out, if they do you may have to adjust he switch so button gets pushed correct amount to open connection.

Are there brake light switch problems in Mercedes?

This is a common problem on Mercedes-Benz models E-Class, C-Class, S-Class, CLS-Class, ML-Class, CLK-Class and other. Too many to list here but the most frequently defective brake light switch problems are seen with E 320 C 240 CLK 500 ML 320 ML 350 S 430 to name a few.

What to do when your brake lights won’t turn off?

Have an assistant stand behind the vehicle. Check if the stopper is on the pedal. Press the brake pedal to gain access to the switch, and press button on the brake light switch. If this does not turn the brake lights off or the button fails to depress all the way, the switch might need to be replaced.

Can a defective brake light switch cause an accident?

Learn how easy it is to change the brake light switch on your Mercedes Benz. Brake light switch issues with Mercedes-Benz cars are the #1 problem that most owners face. Defective brake light switch can cause the lights not to turn on, therefore causing accidents and possibly get you in a middle of a lawsuit you could have avoided.

How do you change the brake light switch?

Check if the stopper is on the pedal. Press the brake pedal to gain access to the switch, and press button on the brake light switch. If this does not turn the brake lights off or the button fails to depress all the way, the switch might need to be replaced.

What do I need to troubleshoot my Mercedes Benz?

Troubleshooting fuel related problems is not very difficult and you can check the fuel pressure yourself. Checking the fuel pressure is very simple. For this test, you will need a fuel pressure gauge. What you need is a fuel pressure gauge with Schrader valve adapter.

What to do if your Mercedes possition sensor is not working?

Don’t start the car. Press and hold the gas pedal for at least five seconds. Keep the pedal pressed. Turn ignition off but do not remove the key. Now release the gas pedal. Remove key. Wait a minute before you restart your Mercedes. This allows resetting the High and Low points of the gas pedal.

What kind of wiring diagram does a Mercedes Benz have?

You will find wiring diagrams for almost all systems on your Mercedes-Benz including: Body, Brakes, Driveline, Electrical Distribution, Engine, HVAC, Interior, Lighting, Restraints, Steering, Suspension, Transmission, Warning Systems.

How to fix no power no start on most Mercedes-Benz?

HOW TO FIX NO POWER NO START ON MOST MERCEDES-BENZ VECHICLES DIY. – YouTube HOW TO FIX NO POWER NO START ON MOST MERCEDES-BENZ VECHICLES DIY. If playback doesn’t begin shortly, try restarting your device.

What happens when the brake pedal goes to the floor?

Brake Lines, Brake Calipers Check: The first thought that comes to anyone’s mind when the brake pedal goes to the floor when engine running, is that there is a leakage in any of the brake lines outflows the pressure in the brake system. The first thing you require is to check the brake fluid level. If it is full capacity, then there is no leak.

What are the problems with a Mercedes Benz?

Top 5 Mercedes-Benz no start problems 1 Engine Click, No Start 2 Engine Dies Right After It Starts 3 Car turns over, but it won’t start 4 The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery 5 Key will not turn the ignition More …

Why is the brake light on my Mercedes not working?

Brake Light Switch. If your Mercedes Benz Drive Authorization System won’t allow you to start your vehicle, it’s more likely that your brake light switch is not working. Gear Selector Module.

Where is the brake light switch on a Mercedes W210?

In the older W210 E-Class, it is located in the back on the back of the pedal. You may need to lay on your back to access the switch. To remove the switch, press on the locking tab and then rotate it clockwise. Step 4. Install new switch Once you remove the old brake light switch, unplug the electrical wires from it.

How to know if your brake light is not working?

1 The brake light stays on when the car is off. 2 Gear selector can NOT be moved out of Park into R, N, D. 3 Brake lights are not working. 4 The car cannot be started. The brake pedal must be pressed to start the engine. 5 Cruise control doesn’t work. 6 ABS or Traction Control light comes on when driving

Why does my Bas light come on in my Mercedes Benz?

To reset the lights, start up your Mercedes-Benz and turn the steering wheel all the way to the right, then all the way to the left. Do this a couple of times. Turn off the engine. Restart. Brake Light Switch may cause BAS / ESP / ABS light to come on. It is the most common problem with Mercedes-Benz cars.

How can I tell if my brake light switch is working?

You may be tempted to check if the brake lights are working to confirm that the brake light switch is working or not. This is not a good test to troubleshoot if the brake light switch is working or not. Common symptom when the brake light switch fails and you can’t get the car out of park is that the ESP, ABS or BAS lights will also turn on.

Why are the tail lights on my Mercedes not working?

All the fuses are clean and new. the turn signals work, but none of the rear lights work. No brake lights, no running lights, no parking lights and no reverse lights. the bulbs are all fine. And the Brake warning light is on in the car, I assume this has to do with that? Is there a tail light relay? W-1-2-3 Go! Are they plugged in?

Read this article on How to replace the brake light switch on a Mercedes-Benz. The shifter assembly (gear shift module) may fail due to wear or internal failure. The shift interlock solenoid which is located inside the shifter assembly can fail or quit working. Plastic parts inside the shifter can break.

What does it mean when the shifter is stuck on a Mercedes?

Shifter can not be returned to Park (P), and you can’t remove the key from ignition. P,N,R,D gear selection indicator on dashboard not displaying correct gear. Mercedes-Benz cars that are equipped with automatic transmission have a gear selector shifter interlock safety feature.

What are the symptoms of a defective brake light switch?

Common symptoms of a defective brake light switch. Car stuck in Park. ABS ESP ETS lights come on. Can not move the shifter from Park to Drive. Car won’t shift gears. Stuck in 2nd gear, limp mode. Brake lights don’t work. (Brake light switch can still be defective even if the brake lights work. Checking the brake light operation is not a good test.)

What causes a Mercedes Benz transmission to get stuck in Park?

After establishing that the battery is fully charged, then check for a defective brake light switch or a damaged shifter module. It is a common occurrence for the Brake Light Switch to fail. It is commonly caused by the transmission stuck in Park problem.

What does it mean when your shifter wont move out of Park?

You start your Mercedes-Benz but realize that the transmission gear selector won’t move out of Park. The shifter can’t be moved from Park (P) to Drive (D). Or you turn off the car but can’t move the shifter back to Park. Don’t panic; this is typically not a transmission problem.

When did Mercedes stop using blink and flash diagnostics?

Mercedes were in parallel developing their own digital diagnostic system and not following the industry standard of OBD1/2. From August 1995 production date Mercedes phased out the analogue type of flash/blink diagnostics in favour of their propriety digital code reading system.

Why does my Mercedes car flash service lights?

Your Mercedes vehicle will flash a host of service lights to inform you when something might be damaged inside the car. If the air conditioner unit is not running normally or is only blowing out warm air, it may be a temporary fault.

What causes a Mercedes Benz air conditioner to blow a fuse?

Finally, check the clutch itself to make sure it is not defective. If there is voltage going to the clutch, a fuse may be blown. A blown fuse would indicate that the system may not have enough refrigerant pressure to tip the low-pressure cutoff switch that cycles the compressor.

What is the fuse box diagram for a Mercedes Benz?

Fuse box diagrams (fuse layout) and assignment of fuses and relays, location of the fuse blocks in Mercedes-Benz vehicles. Fuse box diagram (fuse layout), location, and assignment of fuses and relays Mercedes-Benz 190, 190 E and 190 D (W201) (1982, 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993).

What kind of battery does a Mercedes Benz use?

You can check price and read reviews for multiple Mercedes-Benz AGM Group 94 Batteries that will fit your Mercedes-Benz. You know you have a relatively new battery. You go to start your Mercedes-Benz and you either hear it turn over once or hear several clicks as in this video. This opens in a new window.

What do you do if your shifter is stuck on a Mercedes?

If your Mercedes-Benz automatic transmission gear selector is stuck, you can manually move the shifter from P to D (or D to P) using the shifter override feature found on almost all Mercedes-Benz models, including E-Class, C-Class, CL-Class, ML-Class, SLK-Class and other models.

What happens when you slip in a Mercedes Benz?

When a severe slip happens the WSS informs the computer and the computer informs the ECU to automatically cut engine power temporarily and this is stored as an event or soft code.

What causes a Mercedes Benz to not move out of Park?

If the shifter on your Mercedes-Benz will not move out of park, the first thing your should check is the battery. Once you confirm the battery is fully charged the two most common problems are a defective brake light switch or a shifter module is damaged.

Are there any problems with the Mercedes SLK320?

The chart shows the number of problems reported across all service years for each given model year of the Mercedes Benz SLK320. The 2001 Mercedes Benz SLK320 cars have the most problems reported (42 problems). Table 1. Total number of problems by model year for Mercedes Benz SLK320

What kind of mirror does a Mercedes SLK use?

For many projects on the SLK, it helps to have a bathroom mirror like in the picture to minimize contortionist activities. The tiny extension-rod mirrors are great for certain tasks in cramped quarters, but often a wide angle view is golden.

Where is the brake light switch on a Mercedes Benz?

The general location of the brake light switch can be seen in these photos, it is on the shaft in the footwell that the brake pedal pushes against. The switch is the black plastic part between the red wires and the silver metal brace. 1. Disconnect the negative battery cable.

Can a failed ABS sensor trigger the Bas light?

If you have an ABS sensor that has failed, it will also trigger the ABS, ESP, BAS light. Because the ESP system depends on the ABS system to function properly, the ESP system will also get disabled.

Where is the steering angle sensor on a Mercedes Benz?

Steering Angle Sensor – is right behind the steering wheel in the steering column. It’s the main purpose is to calculate the angle of the steering wheel so that the car knows if you are taking a turn or if you are going straight. The input from the steering angle sensor is used by the ESP control module.

Why is my Mercedes Benz starter not working?

Often times, when the starter is defective or seizes up it will blow out the fuse that protect the starter circuit. Another thing that you can try is to hit the starter with a rubber hammer a couple of times. Depending what kind of starter problems you have, the starter may work a few more times.

How to reset the convertible top on a Mercedes SL500?

The SL500 comes with a variety of features, such as a retractable hardtop. This hardtop is operated by pulling up on a switch to open it, or pressing the switch down to close it. If you cannot get the hardtop to work, and the switch indicator light is flashing, it may be jammed. A jammed hardtop can be fixed by following a reset procedure.

What kind of car is the Mercedes SL500?

The Mercedes-Benz SL500, part of the SL-Class of roadsters, is a two-door car classified as a luxury grand tourer. The SL500 comes with a variety of features, such as a retractable hardtop. This hardtop is operated by pulling up on a switch to open it, or pressing the switch down to close it. If you cannot get the …

Why is my Mercedes Benz EIS not working?

The key has a sequential code to ensure the vehicle is not stolen. Mercedes Benz owner may face the problem that the key no longer turns in the ignition.This issue is often caused either by a defective key, bad shifter module, a failed Electronic Ignition Switch (EIS) also known as the EIS-EZS or a bad steering lock module (ESL).

What causes a Mercedes Benz to not start?

In most cases you will get a fault code related to one of the following: 1 ECM / PCM computer failure 2 Camshaft position sensor 3 Shifter Selector module 4 Fault codes related to driver authorization or immobilizer 5 Electrical problems

Why does my Mercedes Benz make a clicking noise?

It requires electrical power to crank the engine. The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars.

What does the fob remote on a Mercedes Benz do?

The newer keys have a transponder integrated in them. The key fob remote serves two purposes. First it disables the anti-theft system when you unlock the car. Second, Drive Authorization System verifies the key to make sure it is the right key to start the car.

When did the lights go out on my Mercedes?

Mercedes Class A150 Reg 2009. All my lights went out on a recent short drive in early dark morning. Car was left standing for about 14 hours. Lights came back on, on starting. Then, after about 5 minutes travelling they went out again.

Why are the low beams not working on my 96 Vito?

I had a similar problem on my 96 Vito with low beams on both sides not working when the lights where in the on position.

Why are the fog lamps not working on my Mercedes?

Also central locking had ceased working, but after i had removed and replaced black box that carries fuses on steering column – removed and reseated green relays (neither of which appeared to affect dipped beams) – reseated black box – central locking started to work, fog lamps also (up position) started to work.

Is there a brake lamp in the back of the Mercedes W126?

A third brake lamp in the centre of rear windscreen was federally mandated from 1986 model year on for the US version only. In some markets, it was offered as standard or extra-cost option. Early model W126 without airbag, MB-Tex seats, and Zebrano interior wood trim. Right Hand Drive.

When did Mercedes Benz start working on the W126?

From 1973 to 1975, Mercedes-Benz designers worked on the successor to the W116. In December 1975, after several design concepts being presented, the design for the W126 S-Class was approved and frozen in 1976. Design work on the coupe began immediately afterward, being finalized in 1977.

Where can I buy a Mercedes brake light switch?

You can buy a new brake light switch on Amazon for less than $15 USD, just do a search for Mercedes-Benz Brake Light Switches. In the video below you will can see how easy it is to replace the brake light switch on a Mercedes-Benz E-Class.

What kind of suspension does Mercedes Benz W126 have?

Although the top of range Mercedes-Benz 450 SEL 6.9 of the previous generation was not directly replaced, the W126 carried forward the hydropneumatic suspension of the 6.9 as an option on the 500 SEL and later on 420 SEL and 560 SEL models.

What to do if Mercedes Benz ABC system is not working?

Take the car to the dealer or a workshop with a Mercedes STAR diagnostic system (SDS). If the problem is not leak related, then you will need the diagnostic codes to determine what component is having the problem. “Drive Carefully” or “Visit Workshop” comes on the dash and stays.

Why do my Mercedes Benz ESP Lights Come On?

The BAS / ESP / ABS lights is not a problem with just Mercedes-Benz ML320 / ML430 models. It is a problem that has impacted all Mercedes-Benz models. We have included the top causes that trigger these lights to come on in the section below.

How to reset the lights on a Mercedes Benz?

To reset the lights, start up your Mercedes-Benz and turn the steering wheel all the way to the right, then all the way to the left. Do this a couple of times.

What causes a Mercedes convertible top to move slow?

Mercedes Convertible top moves very slow 1 This can be caused by low fluid level or air in the hydraulic lines. 2 Air in the hydrauilc lift cylinders 3 It can be caused by binding of mechanical arms. 4 Weak convertible top lift cylinder. 5 Weak battery or ground connection. 6 Leak at the o-ring at any of the lift cylinders. …

What does it mean when your brake pedal is hard?

Brake Pedal feels hard when pushing on the brakes – This indicates that your brake booster is not working properly or is leaking. There is a seal between the booster and the master cylinder that often goes bad. If the seal is ok it could be a faulty brake booster but not always.

Can a bad master cylinder cause your brakes to not work?

Master Cylinder Bad: A bad master cylinder will cause your brakes to have no pressure. Master cylinders cannot be repaired and will need to be replaced. Sometimes your brakes will still work, but they seem to have grown weak.

What causes brake pedals to jump when replacing a booster?

Be sure to test your vacuum system before replacing an expensive brake booster. Brake pedal jumpy (ABS systems) – This means your ABS system is trying to come on even when not needed. Usually caused by dirty or faulty wheel sensors, air in the system, or an ABS controller going bad. See Kents YouTube video on ABS brakes. UPS GROUND SHIP ONLY!

Where are the spare fuses in a Mercedes W320?

Spare – Spare fuses located in 2nd row (observer correct amperage)- Additional fuses are located underneath the rear seat bench on the right, and the nextr to the light switch in the cocpit- Fuse extractor in car tool kit Fuse box under the seat, near the battery (210 545 05 00): Fuse Ampere rating [A]

Are there any problems with the Mercedes SL550?

THE SPARK PLUGS, VALVE, ENGINE, TRANSMISSION MOUNTS AND CAM PLUGS ON THE LEFT CYLINDER HEAD WERE ALL REPLACED. HOWEVER, TWO DAYS LATER, THE VEHICLE EXHIBITED THE SAME SHAKE AS BEFORE.

Why is the gear selector on my Mercedes not working?

P,N,R,D gear selection indicator on dashboard not displaying correct gear. Mercedes-Benz cars that are equipped with automatic transmission have a gear selector shifter interlock safety feature. This safety feature locks the shifter in Park when you turn off the ignition.

What to do when your brake lights are not working?

In the situation when brake lights are not working properly, you need to make sure that the power is going through and check the fuse. If the brakes lights are turned on at the same time as turn signal lights, you need to bring it to the mechanics for a check.

Where is the brake light switch on my car?

Fuse Box and Light Switch. You have to find the fuse box or the power distribution center (PDC). You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm.

Why does my car not start when I Turn on the key?

This feature is not available right now. Please try again later. One possible reason your car wont start is a bad connection. This is one of those things that is often over looked until after the battery or starter or alternator have been replaced or all of the above. if this happens to you check your battery connections. Loading…

What to do if your Mercedes key won’t turn?

If you have this problem you will have to install a new / virgin EIS. You can not install a used unit because the EIS has to be paired / married to the car using Mercedes-Benz Star Diagnostic Software. They key itself may be the reason why the car doesn’t start. The key may open the doors, but it will not start the car.

How can I tell if my Mercedes remote is working?

Next, we need to check if the remote is sending out a message. The remote emits infrared waves. While you can’t see infrared light with your eyes, there is an easy way to check. Grab your phone and turn on the camera. Point the camera to your phone and carefully see if you notice a light every time you turn you press a button on the remote.

What should I do if my Mercedes key fob is not working?

If you need a replacement battery note that Mercedes-Benz uses CR2025 battery type. Ensure you have new batteries in your key fob. Next, look carefully at your Mercedes-Benz key. When you press the button on your key you should see a small RED led light. The light should light up every time you press any of the buttons (Lock, Unlock, Panic, Trunk).

Why are the lights not working on my Mercedes?

Lights not working – We have seen many Mercedes-Benz where one or a few lights don’t work. It can be that the left or right low beams, fog lights or turn signals may not work. You should always avoid splicing wires to get power for aftermarket HID lights, alarm or connecting a trailer hitch.

What does it mean when your turn signal is not working on Mercedes?

In newer Mercedes models, you will get a warning on instrument cluster stating “Turn Signal Left / Right / Front / Rear / Side Malfunction”. Depending on the Mercedes model and problem a warning may or may not show on the dashboard.

Why is my Mercedes Benz not recognizing my key?

Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred. Please try again later. (Playback ID: ByXeYSrc-y_y4WvS) An error occurred while retrieving sharing information.

What should I do if my turn signal light is not working?

LED lights rarely fail. The first test that you should perform is to disconnect the LED turn signal light and apply power to the LED bulb. Does the LED light turn on? If the LED doesn’t turn on, replace it. If the LED turn signal light does turn on, the LED light is not the problem.

How do you turn off the dash lights?

You should see all the dash lights come on. Do NOT start the car. Position II: You should hear two clicks and all your dash lights should turn on. Do not start the engine. Press the gas pedal all the way. By pressing the accelerator pedal to the floor, you will activate the kick down switch. Keep the gas pedal pressed all the way to down. Wait.

Why does my car shut off at a traffic signal?

There could be numerous reasons for the engine to fail to maintain power at low speeds. You may need to seek professional help because it sometimes needs special expertise to troubleshoot this particular complication. It is quite irritating when your car shuts off while idling, especially when you are at the traffic signal.

Why does my Mercedes-Benz ml-320 shut off?

2009 ML-320 – same problem but happens very rarely, often a month between. Drive 30 minutes with a lot of stop and go. Try to restart a few minutes later, the starter turns over 10 seconds and then stops. Wait 10 minutes and it starts and works perfectly. I replaced the crankshaft sensor a few months back and it has happened twice since then.

What happens when you restart a 1999 ml430?

I own a 1999 ML430, and the one anomally that I experience is that when I try to restart after it dies, the ignition goes into a continuous crank. It gets stuck in that mode and continues to crank unsuccessfully. Do you also experience this?

What to do when your Mercedes Benz shuts off?

Drive 30 minutes with a lot of stop and go. Try to restart a few minutes later, the starter turns over 10 seconds and then stops. Wait 10 minutes and it starts and works perfectly. I replaced the crankshaft sensor a few months back and it has happened twice since then. 23 people found this helpful.

What do the warning lights on my Mercedes mean?

Or, if you have RAC Breakdown Cover, call for recovery. This warning light indicates that there’s a problem with the power steering. For electric powered systems, this problem could be as simple to fix as rebooting a computer. Find a safe place to stop and try turning the car off and back on again after 30 seconds.

What happens to the airbag light on a Mercedes?

If the battery should die on your Mercedes-Benz, the airbag light on the instrument panel may stay on after you hook up a new battery. The oil light indicator also may stay on, and the radio may not work until you reset its code.

When does the ESP light turn on in a Mercedes?

To check, try stopping and restarting the engine. If the light remains on after restarting get it checked at a garage as the ESP system is an important safety feature. If you have a diesel Mercedes, this light will turn on when the engine is warming up.

Why does my Mercedes not start when I charge the battery?

This Mercedes-Benz is not starting because of a low battery. In this case, what you need to do is trickle charge your battery using any of these 12 volt battery trickle chargers. If you need help read this article on How to charge a Mercedes-Benz the right way. Mercedes won’t start, and it’s not the battery.

What causes a Mercedes Benz shifter to stay in Park?

The next possibility is a failed brake shift interlock solenoid. This solenoid releases the shifter from park when you step on the brake pedal. You can check the solenoid by stepping on the brake pedal and listening for a click sound as the solenoid activates. If you hear the click each time you apply the brakes, then the solenoid is probably fine.

What to do if your gears are stuck on a Mercedes?

If your Mercedes-Benz automatic transmission gear selector is stuck, you can be able to move the shifter from park (P) to drive (D) manually using the shifter override feature found on almost all Mercedes-Benz models including C-Class, E-Class, CL-Class, ML-Class, SLK-Class and other models.

Navigation