Is there a problem with my Mercedes door lock?

When taken to a Mercedes specialist, this issue can be relatively easily-isolated. Vacuum door locking systems have been used in many Mercedes models for many years. Because of this, it is typical for older Mercedes models to run into issues with the various system components.

How to Relock a Mercedes Benz ml430 door?

Since the micro switch of the damaged door did not report a Locked /Unlock status to the All Activity Module (AAM), the AAM unlock and relock all the doors repeatedly until all the doors (micro switches) reported the Locked status. Solution: Replace the door lock actuator, door locks will functioned normally again.

How does the automatic lock work on a Mercedes ML320?

The ML is programmed to automatically lock the doors when you start driving. By disabling the automatic lock function, the car won’t try to automaticly lock the doors. Turn the key to position 2, all your cluster lights are on.

Where is the drain seal on Mercedes ML320 door?

Locate the hole at the edge of your door. It is covered by a rubber drain seal that prevents water from coming in the edge of your door, directly lined with your door handle from outside! Use Torx “T27” and unscrew the bolt directly leveled with the entrance cavity. Hint: You do not need unscrew it all the way.

How to replace the door lock actuator on a Mercedes Benz?

The first step in replacing the door lock actuator is to disconnect the battery. Remove the small plastic plate at the bottom of the rear passenger seat. Underneath is a 11mm nut holding the negative terminal from the battery to ground. Remove the nut and pull the cable off.

What to do if your car door lock is not working?

Check your fuse box first to determine if a blown fuse is keeping the lock from working. If so, replace the fuse. You likely have a shorted door lock actuator, which you can replace with a new unit for the lock that is not working. If a door unlocks, but will not lock again, then replace the door switch.

Why is my car not locking or unlocking?

The body control module controls the locking function. If there is a conflict in one of the door locks that tells the module it is not closed or not locked, the module will cycle the locks. First, try replacing the remote battery to be sure it is not causing the issue.

How does a Mercedes Benz door lock work?

These cars use a vacuum operated system to lock and unlock the doors. The system uses a vacuum pump mounted under the passenger seat to either suck or blow air through lines to each door. At each door, there is a vacuum diaphragm that over time can leak and eventually fail.

How to replace the Mercedes W210 door lock actuator?

Now pry out the plastic tab holding the IRE sensor wiring harness to the door (green arrow). Also cut the zip-tie holding the harness to the mounting tab on the left of the door airbag (purple arrow). Pull off the vacuum connection going to the door lock actuator (yellow arrow). Use caution when pulling the vacuum line off.

When did Mercedes Benz start using vacuum operated locks?

Nowadays, electronics are nearly foolproof and are cheap enough to use in almost any application. Mercedes started using vacuum operated locks sometime in the 1970’s, when modern electronics were still expensive and not quite reliable enough to be used in a system that would be used so frequently.

Where is the central locking system on a Mercedes?

The locks are vacuum operated. The pump is next to the battery under rear seat. Do you hear the pump starting when you press the remote, or dash button? 1994 E320 Wagon,1999 E320 Wagon,2000 E 320 Wagon, MGB Track/Rally, ,1988 300E ,more…. Resolved his problem.

What to do if your Mercedes key won’t turn?

If you have this problem you will have to install a new / virgin EIS. You can not install a used unit because the EIS has to be paired / married to the car using Mercedes-Benz Star Diagnostic Software. They key itself may be the reason why the car doesn’t start. The key may open the doors, but it will not start the car.

What are the common problems with Mercedes key fobs?

Common Mercedes Key Fob Problems Go to top 1 Mercedes key fob not working after battery change 2 Mercedes remote doesn’t work anymore 3 Keyless remote doesn’t lock/unlock the car 4 Mercedes key fob won’t unlock doors 5 Panic button doesn’t work 6 Trunk unlock doesn’t work

Why does my Mercedes C class door lock not work?

This article applies to the Mercedes-Benz C-Class w204 (2007-2014). Due to their frequent use, the springs in the door lock actuator mechanism wear out over time. This can result in the car’s locks malfunctioning; whereupon, they either don’t work at all or otherwise bounce up and down.

What to do if your Mercedes Benz key fob is not working?

1. Put the key in the ignition. 2. Quickly remove it within 10 seconds and hold down the Lock button. 3. While holding the Lock button, press Unlock five times. 4. Release these buttons and press the Trunk button once.

What to do if your central locking system is not working?

If the fuse does not do it, take a picture of the unit and mark and number all the lines going to the unit. Open the Unit and see if the motor is burnt. (won’t turn) Look into the back of the motor with a light. If it looks burnt, you’ll need to remove it.

Why is my car door lock not working?

If your car door lock actuator is not working properly, a common problem is that the plastic air reservoir (at the bottom of the actuator) is broken or cracked. Air leaks will cause the actuator to not be able to pull the door to the close position. This rebuilt kit is designed to fix the problem without changing the complete assembly. Loading…

What to do if your vacuum door lock fails?

Diagnosing the problem begins with isolating the exact source of the issue, or the exact part of the vacuum door locking system that needs repair or attention. Every door lock in your vehicle operates with an actuator. When they fail, it can lead to problems locking one or more door.

Where does the rod go in a door lock?

It turns out that there is a rod that goes from the door lock to the vacuum actuator…when I took the door lock out (after great explanation from a post here) I noticed that the rod was missing. It appeared that it fell into the door. I posted again to see if anyone knew where I could buy one of these parts.

What kind of door lock bounces up and down?

This was done on a 2004 Mercedes C230 Kompressor Sport Coupe. The issue of the Mercedes door lock actuator bouncing up and down affects the W203 C-class and W211 E-class models. This fix does not require you to remove the door panel. You’re welcome. Loading…

Where is the vacuum pump on a Mercedes?

However, sometimes it’s simply more effective to replace the actuators themselves. On most Mercedes models utilizing vacuum locking systems, the vacuum pump is located beneath the front passenger side of the vehicle. The point of this pump is to suck in and blow out air that controls the door locking mechanism.

Why does my 2005 Mercedes Benz S600 not lock?

2005 S600, doors won’t lock and unlock, soft close doors don’t work, rear headrests won’t go down, trunk won’t open. Problem with pneumatic system, auto assist doors don’t work, trunk doesn’t close properly unless you pull switch in hole inside to the left, driver door unlocks much slower than rest. Doors won’t lock or open. Truck does not open.

What’s the price of a Mercedes Benz door lock?

Problems with the pneumatic system can cause closing assist and door lock issues. The average cost for a Mercedes-Benz S500 General Diagnosis is between $143 -$180. Learn More The central locking system does not work from the smartkey nor from the interior buttons.

Why are the doors not working on my Mercedes S500?

ITS A REOCCURRING PROBLEM, A TEMPORARY FIX FOR MOST OF THE SYSTEM IS REPLACING THE FUSE IF THE PROBLEM CONTINUES FOR ONE ITEM AND NOT THE OTHERS (I.E. THE TRUNK STILL DOESN’T WORK BUT THE DOORS DO.) THEN ITS USUALLY PRESSURIZATION ISSUE AND EVEN THAT CAN BE A SIMPLE FIX IF YOU CAN FIND THE AIR LEAK.

Why is my smart key not working on my Mercedes S500?

Smart key won’t open door, battery is fine. Can’t unlock doors or trunk from switches inside. Blade key was working fine for several months, now would not totally release drivers door had to get roadside assistance to manually unlock.

What should I do if my Mercedes key fob is not working?

If you need a replacement battery note that Mercedes-Benz uses CR2025 battery type. Ensure you have new batteries in your key fob. Next, look carefully at your Mercedes-Benz key. When you press the button on your key you should see a small RED led light. The light should light up every time you press any of the buttons (Lock, Unlock, Panic, Trunk).

How do you sync the remote on a Mercedes?

Instructions on how to sync Mercedes remote: Insert the key into the ignition. Quickly remove key from ignition and within 10 seconds hold down the lock button. Continue holding the lock button, and at the same time press, the unlock button five times. Next release all buttons and press the gate/trunk button one time.

Why is my driver’s side door lock not working?

Thanks to the good people here at Benzworld.org I was able to fix my driver’s side door lock without involving my mechanic or having to buy parts. This seems to be a huge issue with W202’s and something that many of you will also deal with. My driver’s side door lock stopped working.

Why is my Mercedes Benz door lock not working?

THEN ITS USUALLY PRESSURIZATION ISSUE AND EVEN THAT CAN BE A SIMPLE FIX IF YOU CAN FIND THE AIR LEAK. Auto assist door closing and locking stopped working. Truck has to be manually opened. Patched a leak in the line but still won’t work.

What to do if your Mercedes SL Class R129 is running rough?

Check your charging system. If your engine is running rough and misfiring you may need to change your cap, rotors and wires. If your valve cover gaskets are leaking we will show you how to replace them. Engine running lean/rough. Maybe you have a vacuum leak. If you engine is only running on one bank of cylinders you may have a bad coil.

Why does my Mercedes SL Class make a clicking noise?

Uneven tire wear and unusual handling in turns can be caused by worn suspension links. Check your rear rearward upper link. A light clicking noise from your rear suspension over bumps can be the result of worn sway bar links. Is your rear ride height lower than normal or do you want to install lowering springs?

Why is my central locking system not working?

Thanks in advance for your help. 1994 E320 Wagon,1999 E320 Wagon,2000 E 320 Wagon, MGB Track/Rally, ,1988 300E ,more…. may have interrupted the com between the module and the pump.Next step before more drastic measures is a reset of the system.

How do I Sync my Mercedes fob to my car?

To synchronize a Mercedes-Benz key to your car all you need to do is insert the key into the ignition for a few seconds. This works in most cases but every now and then you may need to follow further instructions to synchronize your Mercedes key fob remote with your car.

When did the Mercedes SL500 R129 go away?

They used a little less fuel than the first four speed automatic SL500s. By 1996 the new 5 speed transmission increased the fuel economy of the V8 SL500 to within 1 or 2 MPG of the SL320, thus the SL320s went away in 1998. Today you can get a beater early 1990’s 300SL for about $10,000.

When did Mercedes SL500 body style come out?

This R129 body style SL500 was made from 1990 through 2002. It was called the 500 SL from 1990 – 1993.

Where are the fuses on a 1998 Mercedes SL500?

Interior Fuse Box Location: 1990-2002 Mercedes-Benz SL500 – 1998 Mercedes-Benz SL500 5.0L V8 Electrical components such as lights, heated seats and radios all have fuses in your 1998 Mercedes-Benz SL500 5.0L V8. This free video shows you how to replace a blown interior fuse on a 1998 Mercedes-Benz SL500 5.0L V8

How to disable automatic lock on Mercedes ML320?

The ML is programmed to automatically lock the doors when you start driving. By disabling the automatic lock function, the car won’t try to automaticly lock the doors. Do this: Turn the key to position 2, all your cluster lights are on.

How to fix a broken actuator on a Mercedes Benz?

STEP BY STEP! 1.) Determine which door has the broken actuator. Manually unlock all the doors. Lock your doors. One of them will still be unlocked. Manually lock all the doors. Now unlock them. One of them will still be locked. If your doors work properly. Check the lift (trunk) gate. 2.)

How to fix Mercedes bouncing door lock actuator?

If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: Eb8C2fsc3HbLd-fk)

Why does my Remote key not unlock the door?

When the physical key can lock or unlock the door, be sure that the mechanism of the locks is fine. There could be an electrical issue that prevents the fob from connecting to the door’s receiver sensor. These are mostly the reasons and troubleshooting options when a remote key won’t unlock car door.

How can I tell if my Mercedes remote is working?

Next, we need to check if the remote is sending out a message. The remote emits infrared waves. While you can’t see infrared light with your eyes, there is an easy way to check. Grab your phone and turn on the camera. Point the camera to your phone and carefully see if you notice a light every time you turn you press a button on the remote.

Why does my Mercedes-Benz remote lock not Beep?

By MY2006, they should all chirp. And the chirp is not the vehicl’s fanfare horn – it’s the actual alarm siren that produces the noise. Sometime after the MY2005 facelift, MBZ changed the system to chirp by default, without the need for the “Netherlands” setting. It was phased in slowly, with the E-class first, then the CLK, and others.

How to discuss a Mercedes Benz door lock problem?

Start a new thread on your specific issue. Also try using the ‘search community’ at the top of your webpage for other threads on the w202 forum and even the w210 forum. ===>>> Update your user CP info…. Did you find the recommended reading relevant to this discussion?

What are the symptoms of door lock failure?

Symptoms of lock actuator failure may include: odd noises coming from the door locks when the button is pressed or odd behavior coming from the door locks, like spontaneously locking and unlocking unprovoked.

Why is my door lock failure occurs in a BMW?

While your door locking system might seem simple, there are many areas for malfunction and failure. In other words, the problem could be due to several factors that aren’t performing well, and the source of the problem will dictate how your reliable BMW specialist goes about fixing it.

What causes a door lock relay to not work?

Power door locks do not function. Power door locks that do not function are another common symptom for a problem with the door lock relay. If the power door lock relay fails, it will cut off power to the entire power door lock system and may cause them to not function correctly.

What causes a Mercedes Benz key to not turn?

List of common problems and possible solutions 1 Locked Steering Wheel. New drivers always experience this at least once, so we thought we would include it in this list. 2 Discharged Battery Undervoltage. 3 Key Tumbler Defective. 4 Defective Electronic Ignition/Switch System EIS / N73. 5 Smart Key Remote. …

Where is the Master Lock on a car?

Power locks are convenient, and the master lock control on the driver side allows you to lock and unlock all the doors in the car. Here’s how to use it: Press the end of the switch with the closed…

How do you activate or deactivate the auto lock feature?

Turn the ignition off. Press the Unlock button three more times. Turn the ignition back to on. The horn should beep once. This tells you that you’re now in programming mode. Press the Unlock button, then press Lock again. The horn will beep once to tell you that Auto Lock was deactivated.

Are there any problems with Mercedes Benz COMAND system?

We have listed down common issues with the Mercedes-Benz COMAND system, including problems with The most common solution to fix any of these issues is to try to perform a soft reset of the COMAND unit.

What are the problems with a Mercedes Benz?

Top 5 Mercedes-Benz no start problems 1 Engine Click, No Start 2 Engine Dies Right After It Starts 3 Car turns over, but it won’t start 4 The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery 5 Key will not turn the ignition More

What should I do if my Mercedes Benz won’t start?

Start the car and you should be able to get around 60 psi. When the engine is running and when you turn off the engine the pressure should stay steady. Always perform this test on a cold engine. Next, make sure that the fuel injector connections are secure and not loose. Check the fuel pump and the fuel pump relay.

Why does my Mercedes Benz make a clicking noise?

It requires electrical power to crank the engine. The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars.

How to change lock modes on Mercedes SLK?

Check PSE for corrosion or water ingress. Plenty of posts on this in the stickies. There are two central lock ing modes – driver door only and global (all doors). See the drivers manual. You can change between modes with the remote (when working) by holding the lock button for 5 seconds till the LED on the fob flashes.

Where are the fuse boxes in a Mercedes Benz SLK?

There are 3 fuse boxes in your slk. One in the engine bay. One in the trunk. One on the driver side when you open the door and look at the side where your headlight switch is. You need a coin to twist 90% the two 1 inch wide plastic tabs to open the side panel. Youll find the last fuse box inside.

Navigation