How to run a diagnostic test on a 1993 Chevy truck?
They will be on the end of the row to the far right, and the will be side by side. Place your key into the Chevy’s ignition and turn it, but don’t crank the engine. Watch the “check engine” light. It will start flashing. Chevy trouble codes are two digits. The first digit will be represented by a long flash.
How to troubleshoot a no start GM 4.3L pick up?
Testing a Cranks but Does Not Start condition on your GM 4.3L, 5.0L, 5.7L pick up, van or SUV is not that hard to do, if you have a solid diagnostic strategy. In this article I’ll show you the basics of testing such a problem.
What kind of engine does a C / K pickup truck have?
At its 1988 launch, the fourth-generation C/K pickup trucks shared its five-engine powertrain offering with the R/V series. On 1500 series vehicles, a 4.3 L Vortec V6 was standard, with the options of a 5.0 L V8, 5.7 L V8 and a 6.2 L diesel V8.
When did the fourth generation Chevy C / K come out?
For 1988, the fourth-generation C/K was introduced, including (nominal) 1⁄2 -ton, 3⁄4 -ton, and 1-ton pickup trucks and chassis cabs. In a nomenclature revision, GM adopted the 1500/2500/3500 payload series (previously used by GMC) for all full-size trucks (the Rounded-Line R/V series would do so for 1989).
What kind of car is 1993 Chevy Cheyenne?
Clean CARFAX. 6.5L V8 Turbodiesel. 1993 Chevrolet C/K 2500 Cheyenne 6.5L V8 Turbodiesel RWDwww.pinnaclenissan.com , Excellent selection of New and Used vehicles, Financing 1993 Chevrolet C/K 2500 Cheyenne RWD 5.7L V8 EFIAll Jeff Wyler Pre-owned vehicles come with a FREE car-fax report.
Is the 1993 GMC 1500 a good truck?
Showing 3 of 497 reviews. Everything i put at this truck it still works I got the amazing 350 vortec aka the 5.7L v8 this truck runs good and smooth the steering is loose but its okay Led lights all around, z71 off road package (skid plates, 4×4, g80 rear locking differential). clean interior and exterior with only two dents in the tail gate.
What are the specs of a 1993 Chevy Blazer?
This 1993 Chevrolet Blazer Cheyenne features: Entertainment Features AM/FM radio Speakers : 2 Specs and Dimensions Engine horsepower : 210hp @ RPM Engine displacement : 5.7 L Engine torque : 300 lb.-ft. @ RPM GVWR : 2,835kg (6,250lbs) This 1993 Chevrolet C/K 3500 series dully pickup will make someone a great work truck.
What’s the name of the fourth generation Chevy truck?
The fourth-generation C/K pickup trucks were marketed by the Chevrolet and GMC divisions of General Motors. Offered in 1500 ( 1 ⁄ 2 -ton), 2500 ( 3 ⁄ 4 -ton), and 3500 (1-ton) payload series, the C/K pickup trucks were sold in two-door standard cab, two or three-door extended cab, and four-door crew cab configurations.
Where is the ASDL connector on a 1993 Chevy truck?
Locate the ASDL connector in your ’93 Chevy truck. It should be on the driver’s side, under the dash and near the steering column. It is made of plastic and has 12 pin-receiving slots. Bend a paper clip into a straight wire, then bend it into a tight “U” shape. Place both ends of the U-shaped paper clip into the ASDL.
How do you connect a voltmeter to a diagnostic connector?
1. Connect voltmeter. Remove the cover, if present, from the diagnostic connector. With the ignition in the OFF position, connect the leads of the analog voltmeter as shown below, positive lead to terminal 1 and negative lead to terminal 12. I add some tape to the clips to be sure they do not short against an adjacent terminal.
Where can I Find my GM trouble code?
If you own a 1982 to 1995 GM car or truck, you just might be able to read your trouble codes for free! If you have a connector like this under your dash, read on… (note: this connector may have a black plastic cover over it, so also look for a cover shaped like this, sorry for the messy wires here)
Where to insert jumper wire for service check light?
Turn the key to the “on” position to confirm that the Malfunction Indicator Light (MIL) functions. With ignition off, insert jumper wire in service check connector terminals, located behind right side of dash. Image shows connectors and locations Turn ignition switch to ON position.
They will be on the end of the row to the far right, and the will be side by side. Place your key into the Chevy’s ignition and turn it, but don’t crank the engine. Watch the “check engine” light. It will start flashing. Chevy trouble codes are two digits. The first digit will be represented by a long flash.
Where is the service check connector on my car?
The service check connector is under the glove box. It should normally be connected to the connector cover located under the glove box but it may have come loose or be tucked behind other wires or the speaker box.
If you own a 1982 to 1995 GM car or truck, you just might be able to read your trouble codes for free! If you have a connector like this under your dash, read on… (note: this connector may have a black plastic cover over it, so also look for a cover shaped like this, sorry for the messy wires here)