What kind of oil does a 2010 Mazda take?

What kind of oil does a 2010 Mazda take?

The 2010 Mazda Mazda3 uses 2.5 liters (2.6 quarts) of SAE 5W-30 engine oil. This is a very popular synthetic fluid suitable for a wide variety of engines in a large range of climates. Mazda recommends changing this fluid every 6,000 miles or 6 months, whichever You arrive to first.

How often does a 2010 Mazda 3 need an oil change?

between 7,500 and 10,000 miles
The oil in your Mazda model should be changed between 7,500 and 10,000 miles. However, for a more precise number, check your vehicle’s owner’s manual.

What kind of oil does a 2010 Mazda 6 take?

Mobil 1 Extended Performance Synthetic Motor Oil 5W-20 1 Quart.

How do you reset the oil life on a 2010 Mazda 6?

To perform a 2010 Mazda6 oil light reset You will need to change the oil and then press the reset button. When performing an oil change on the car You will first want to make sure that the vehicle has been parked and off for a couple of hours.

How to change the oil in a Mazda 6?

1. Getting Started – Prepare for the repair 2. Open the Hood – How to pop the hood and prop it open 3. Find Oil Drain – Locate the oil drain plug underneath the vehicle 4. Drain Oil – Set up the workspace, drain oil and replace plug 5.

What kind of oil does a Mazda 3 use?

If your 3 is too low to the ground to access your drain plug and oil filter, be sure to use jack stands and safe jacking procedures before getting under your 3. Most Mazdas have the oil type printed on the oil cap – it will likely be 5W-20, 5W-30, 5W-40, 10W-30 or 10W-40.

How to change the oil in a BMW Z3?

3. Find Oil Drain – Locate the oil drain plug underneath the vehicle 4. Drain Oil – Set up the workspace, drain oil and replace plug 5. Find Oil Filter – Locate the oil filter 6. Remove Filter – Position drain pan and remove the oil filter 7. Replace Filter – Add oil to the new oil filter and insert it

What kind of oil is in a Mazda Tribute?

Most Mazdas have the oil type printed on the oil cap – it will likely be 5W-20, 5W-30, 5W-40, 10W-30 or 10W-40. If it isn’t printed on the oil cap, check your owners manual for the exact type before adding new oil.

1. Getting Started – Prepare for the repair 2. Open the Hood – How to pop the hood and prop it open 3. Find Oil Drain – Locate the oil drain plug underneath the vehicle 4. Drain Oil – Set up the workspace, drain oil and replace plug 5.

What kind of oil does a Mazda MZR use?

1. Engine oil viscosity rating change for the MZR 2.0 L and 2.5 L engines from SAE 5W-20 to SAE 0W-20 after the 2010 MY. 2. M/T oil viscosity and Service Rating change for all models after the 2010 MY from SAE 75W-90, GL-4 or GL-5 to SAE 75W-80, GL-4

Why did Mazda change the oil in the M / TS?

According to Mazda, some related parts were changed in the M/Ts due to the oil specification change. Consequently, if SAE 75W-90 is used in transmissions designed for SAE 75W-80, an increase in fuel consumption and harder shifting when cold can result.

How to replace transaxle fluid in Mazda 3?

The Automatic Transaxle Fluid (ATF) Replacement section specifies the proceedure as follows: 1. Remove the oil dipstick. 2. Remove the drain plug and washer from the transmission oil pan. 3. Drain the ATF and install the drain plug with a new washer.