How to replace CV axle seal in Mazda3?
How-To: CV axle / seal replacement. Figured this is something that most of us will need to do at least once in the ownership of our cars, so I thought I’d throw up a how-to while doing it. My drivers side CV axle seal shot craps the other day thus causing my transmission to leak like niagra falls.
When does the axle seal need to be replaced in a car?
In a typical front-wheel drive car, the hardest part is to remove the CV axle (driveshaft) to get to the seal. Without a hoist and proper tools it’s quite difficult, especially if the seal is leaking on the side of the longer driveshaft (the right side in most cars).
How big is the seal on a Mazda 3?
There are 3 bolts total that you need to remove in order to do this. 2 on the rear of the control arm on the bottom, and one on the front facing the front of the car. The two bolts on the rear are 17mm, and I believe the one on the front is 19mm. I’m not too sure of this though, it may be larger, but no bigger then 22mm.
Which is easier to replace CV axle or seal?
A piece of road drebris came up and smacked the crap out of the copper shield thats on the cv axle and sent it into the seal tearing it to kingdom come. Personally, I think the passenger side is a little bit easier to work with for the axle, just because of the way its laid out.
How-To: CV axle / seal replacement. Figured this is something that most of us will need to do at least once in the ownership of our cars, so I thought I’d throw up a how-to while doing it. My drivers side CV axle seal shot craps the other day thus causing my transmission to leak like niagra falls.
When do you need an axle seal replacement?
Let’s start with the first question. The axle seal replacement is not a part of regular maintenance, the seal only needs to be changed if it leaks. How do you know if an axle seal is leaking? Gear oil or transmission fluid drops on your driveway are some of the early signs.
There are 3 bolts total that you need to remove in order to do this. 2 on the rear of the control arm on the bottom, and one on the front facing the front of the car. The two bolts on the rear are 17mm, and I believe the one on the front is 19mm. I’m not too sure of this though, it may be larger, but no bigger then 22mm.
What is the job of an axle seal?
The job of an axle seal is to keep the transmission fluid or differential oil from leaking out. In some all-wheel drive vehicles, one of the front CV axles is connected to the transfer case (unit). Front CV axle (driveshaft) seal.
How to replace an automotive CV axle-2carpros?
Reinstall the CV Axle Nut Reinstall the CV joint axle nut by hand to avoid cross threading and then tighten to manufactures specification with is usually between 120 and 140 foot pounds for torque. Install a new cotter pin and then bend one end if it over the axle threads to hold it in place while cutting off any excess and you are all set.
How do you remove a drive shaft on a Mazda 3?
1. Install a spare nut onto the drive shaft. 2. Tap the nut with a copper hammer and separate the drive shaft from the axle. 3. Separate the drive shaft from the wheel hub. 4. Separate the drive shaft (LH) from the transaxle using the SSTs
How to replace a CV axle in your car, DIY?
CV axle replacement. How to replace a CV axle in your car, DIY with Scotty Kilmer. How to remove CV axle. If the CV joint is clacking as you accelerate and turn at the same time, you need a new axle. DIY car repair with Scotty Kilmer, an auto mechanic for the last 44 years. 1. Tie Rod Remover Tool: http://amzn.to/2kqdAke 2.
What’s the German method for CV axle replacement?
For everything else, I use the german method, “goodentight” or the half vien method, which is when you see half a vein popping out of your arm, that will let you know when things are tight*
How to replace a passenger side axle nut?
If you don’t have access to air tools, what you’re going to do is remove the center cap on your wheel, reinstall it with 3 lug nuts, put the car on the ground, and set the parking brake. Then you’re going to stick the 32mm or 1 1/4″ socket with breaker bar and pipe through the center hole in the wheel and use that to break the axle nut loose.
How do you remove a strut from a car?
The first step to removing the strut is to remove and loosen the bolts on the top hat. You’ll want to completely remove the bolt closest to the fender and loosen the other two about half way. This will give the strut a little wiggle room and make it slide out of the spindle easier.
How to take an axle out of a Mazda 6?
If you’re having trouble taking out the CV axle, use a 15mm socket to dismount the strut tower from the lower control arm. This will free up some room for the axle to come out. 9.
What kind of steering knuckle assembly does Mazda use?
Front Driver Side Steering Knuckle Assembly (LK015) by MOOG®. Quantity: 1 per Pack. This product is made of high-quality components to meet and exceed strict quality requirements. Designed using state-of-the-art technology and with…
Where is the CV axle nut on a Mazda 6?
The CV axle nut is located in the middle of the hub. If the nut is difficult to remove due to rust or something else, use a rust penetrant. Gather together a pry bar, breaker bar, and 32mm socket. Use the pry bar to hold the rotor in place, connect the socket and breaker bar to the lug nut, and then push down the breaker bar with your foot. 4.
1. Install a spare nut onto the drive shaft. 2. Tap the nut with a copper hammer and separate the drive shaft from the axle. 3. Separate the drive shaft from the wheel hub. 4. Separate the drive shaft (LH) from the transaxle using the SSTs
How to repair the front drive shaft on a Mazda CX-5?
1. Apply transaxle oil to the oil seal lip. 2. Apply grease (L2Y1 33247) to the wheel bearing inner race and drive shaft contact surface (Area A in figure). 3. Insert the drive shaft into the wheel hub. 4. Install the drive shaft to the transaxle.