How to replace the timing belt on a Lexus LS400?
Disconnect the camshaft position sensor connector from the ignition coil bracket. Disconnect the sensor wire from the timing belt cover. Remove the wire grommet from the timing belt cover. Disconnect the wire clamp from the timing belt cover. Unplug all the wires from the rotor caps and remove the rotor caps.
What happens if the timing belt breaks on a LS?
The first gen LS’s (1990-1994) have a non-interface engine, so if the timing belt breaks it’s not going to damage the engine. If it breaks you’ll just be stranded. Some belts break and some last. Timing belt & water pump parts kit There are several kits like this one available for this job.
How many miles does a 1996 Lexus LS 400 have?
– Post Questions Here For Quick Answers! Car is a 1996 Lexus LS 400 with 115k miles. Click Here for First Generation Timing Change The most important thing is put the parts that you take out in the order they were removed otherwise its really easy to get lost and you can have some extra parts after assembly.
How do you install a timing belt on an idler?
Run the belt over the No. 1 and No. 2 idler pulleys and under the water pump pulley. 35) Install the timing belt guide; see step 23 to see how it should look, then press backspace to return here. 36) Install the timing belt cover spacer; see step 22 to see how it should look, then press backspace to return here.
How to remove the crankshaft pulley on a Lexus?
To remove the crankshaft pulley you might need a compressor if you are doing the job alone. Otherwise all u need a strength in your hands. To get the crankshaft pulley out you have to rent a special tool caller “harmonic balancer pulley removal kit”. The rent is free at Autozone. Parts.
How many miles does a Lexus LS 400 have?
Car is a 1996 Lexus LS 400 with 115k miles. Click Here for First Generation Timing Change The most important thing is put the parts that you take out in the order they were removed otherwise its really easy to get lost and you can have some extra parts after assembly. In order to get this done you need a big 500 piece set of tools.
Disconnect the camshaft position sensor connector from the ignition coil bracket. Disconnect the sensor wire from the timing belt cover. Remove the wire grommet from the timing belt cover. Disconnect the wire clamp from the timing belt cover. Unplug all the wires from the rotor caps and remove the rotor caps.
The first gen LS’s (1990-1994) have a non-interface engine, so if the timing belt breaks it’s not going to damage the engine. If it breaks you’ll just be stranded. Some belts break and some last. Timing belt & water pump parts kit There are several kits like this one available for this job.
To remove the crankshaft pulley you might need a compressor if you are doing the job alone. Otherwise all u need a strength in your hands. To get the crankshaft pulley out you have to rent a special tool caller “harmonic balancer pulley removal kit”. The rent is free at Autozone. Parts.
How do you change the water pump on a Lexus LS400?
Use a strong screwdriver or pry bar between the water pump and cylinder block to pry it off, be careful not to damage the block. Clean all the old sealant, grease, coolant, and dirt off the cylinder block. Here’s what it will look like with the water pump removed and everything cleaned up. 29) Replace the O-ring on the water by-pass pipe.
Where is the timing belt on a Lexus LS400?
41) Check to make sure the timing marks on both camshaft timing pulleys line up with the marks on the engine (white marks), then pull on the belt and install it onto the LH camshaft timing pulley. The “L-CAM” line on the timing belt should run right in between the marks.
What kind of engine does a Lexus LS400 have?
The 4.0 L eight-cylinder motor was also used in these vehicles. The output produced is 260 hp and 270 lb-ft of torque at 4500 rpm. Vehicles in this generation were fitted with either a 4-speed or 5-speed. What are engine options for third-generation Lexus LS 400s?