How much HP does it take to pull a disk?
If the operator has enough sense to keep the speed down (around 5-5.5 mph is good) then more hp is fine, if you’ve got someone who has to go as fast as they can pull it then less is better. I would want a minimum of 160 hp and mfwd on a 24′ disk.
How many horsepower does it take to pull a 12 foot disc tractor?
A twelve foot disc is a load for a seventy hp. john deere 3020 if you have it cutting hard and deep.
How big of a disc can a 40 hp tractor pull?
From what I read, the recommended weight for up to a 40 HP Kubota is a 575 lb disc with looks to have minimal offset. The more the offset, the more HP is used to pull it. Some say 10HP per foot of offset for a double gang. So a 6 foot double gang offset would be a 60 HP tractor.
How big of a disc can a 100 hp tractor pull?
For discing 4-5 inches deep your tractor should be able to handle a 14′ tandem disc very nicely. If you want to go deeper then you will need to go smaller.
How much horsepower does it take to pull a 20 foot disc?
Subject: RE: Typical Hp requirements for a 20 foot disk? 150 is plenty. 120 would even do it.
How much horsepower does it take to pull a 14 foot disc?
It would take 100+ HP to pull a 14 foot IH 500 series in heavy soil.
How much horsepower does it take to pull 10 discs?
Well, the verdict is in and a j.d. 1530 45 hp tractor will pull a 10 ft. disc in 5th gear with relative ease.
How much does a John Deere 210 cost?
John Deere 210 tandem disk, off-set gangs, 20:” front blades, 21″ rear, 9″ spacing, spring tightening scrapers, new tires, no welds, bends, or breaks, field ready.. About 15’ 210 disc. Some front blades need replacing. Good size blades $2500
How big are the blades on a John Deere 210?
JOHN DEERE 210 DISC, 13’10” WORKING WIDTH, DUAL WHEELS, 9″SPACXING, FRONT BLADES ARE 19.25″, ONE HAS A BEND IN THE FRONT, REAR BLADES ARE 20.5″ GOOD COND, BEASRINGS AND SCRAPERS ARE ALL GOOD, HAS FURROW FILLER BLADES ON THE REAR GANG, , HAS A LBI HITHICKER SINGLE BAR HARTROW ON THE BACK… John Deere disc 210 model.
How big of a disk do you need for a tractor?
The trouble is there are heavy offset disks that take 350 hp tractors to pull less than 20 feet, and there are little finishing disks with the blades worn down to 14-15 inches on easy ground that don’t need 40 hp for a 12 foot disk…… In general I’d put a 10 foot average finishing dik behind a 50 hp tractor.
How much engine hp do you need to pull a disc?
YOu need to pull a disc at 5-6 mph to get it to work effectively. I have plenty of hp in dry soil. If the soil is wet, then the disc digs deeper and loss of traction is a problem. So my guess is you’ll need 5-10 engine hp to operate a disc like this.
John Deere 210 tandem disk, off-set gangs, 20:” front blades, 21″ rear, 9″ spacing, spring tightening scrapers, new tires, no welds, bends, or breaks, field ready.. About 15’ 210 disc. Some front blades need replacing. Good size blades $2500
JOHN DEERE 210 DISC, 13’10” WORKING WIDTH, DUAL WHEELS, 9″SPACXING, FRONT BLADES ARE 19.25″, ONE HAS A BEND IN THE FRONT, REAR BLADES ARE 20.5″ GOOD COND, BEASRINGS AND SCRAPERS ARE ALL GOOD, HAS FURROW FILLER BLADES ON THE REAR GANG, , HAS A LBI HITHICKER SINGLE BAR HARTROW ON THE BACK… John Deere disc 210 model.
How many horsepower does a John Deere tractor have?
7R Series Tractors 210 to 290 engine horsepower. The New 7R Series Tractors combine the power of a row-crop with the versatility of a utility tractor. 6R Series Tractors 170 to 210 hp.
How big is a John Deere 2680h tillage disk?
This two-season tool can operate up to 22.5 km/h (14 mph) in field. This tool is available in fifteen configurations from 2.4 m to 13.7 m (8 ft to 45 ft). The 2680H requires 34.25 kW/m (14 hp/ft), but in certain hilly, soft or wet conditions it may require an additional 25% engine horsepower to maintain operating speeds at preferred working depth.