How to replace front wheel bearing on Jeep Grand Cherokee?

Have yr. 2000, 4.7 L, Grand Cherokee. Looking for step-by-step instructions for replacing front wheel bearing. ah, its a piece of cake. Jack up the vehicle, remove the wheel and ofcourse use a jack stand. I do one side at a time because it might take a lot of torq to get the hub bolts loose. Take off the caliper and brakes.

How do you remove the knuckle on a Jeep Cherokee?

remove the 3 bolts that hold the knuckle on (1/2 12pt). take a hammer and hit around the inside of hub until it comes off. Once it is off take some sand paper and clean up the rust where the hub and knuckle push together. On my Jeep I have aftermarket wheels so I am able to access the main hub nut with the wheel still on.

How can I tell if my front wheel bearing is bad?

Raise the front wheels off of the ground so that you can spin the wheels freely with your hand when the vehicle is in neutral. Be certain that the vehicle is securely supported. As you spin them, one at a time, gently place your hand on the coil spring and feel for vibrations. A bad wheel bearing is usually quite noticeable by feel.

Why do front wheel bearings make a moaning sound?

Wheel bearings usually make a moaning sound. Sometimes they’ll sound like you have big knobby tires going down the road (if you do have these tires, it would be hard to tell). If it gets really bad you’ll get excess heat from that bearing. You can sometimes jack the wheel up and pull it in and out slightly.

How long does it take to replace wheel hub on Jeep Cherokee?

Please try again later. How to replace a wheel bearing (wheel hub) on a Jeep Cherokee. This Cherokee has a sealed hub unit. Older models have a separate bearing that require additional tools to press the old bearing out and the new one in. With a hub replacement, the repair should only take a half an hour barring any problems with seized bolts.

How can I tell if I need a front wheel bearing replacement?

A fairly simple way to tell is to, first block your rear wheels for safety. Raise the front wheels off of the ground so that you can spin the wheels freely with your hand when the vehicle is in neutral. Be certain that the vehicle is securely supported.

How to replace rear axle seal on Jeep Grand Cherokee?

This video shows you how to go through the process of replacing a leaking rear axle seal on a WJ (1999-2004) Jeep Grand Cherokee. This procedure would be very similar for many other solid axle Jeeps as well as many other vehicle makes and models. Loading…

How to replace a wheel bearing on a Jeep Cherokee?

How to replace a wheel bearing (wheel hub) on a Jeep Cherokee. This Cherokee has a sealed hub unit. Older models have a separate bearing that require additional tools to press the old bearing out and the new one in. With a hub replacement, the repair should only take a half an hour barring any problems with seized bolts.

How do you replace the wheel bearing on a car?

Finally, the brake rotor and brake caliper are re-attached, the wheel installed and the car is road tested. On vehicles where the wheel bearing is pressed into a cavity within the steering knuckle, the steering knuckle must be removed from the vehicle in order to press out the old bearing and press in the new bearing.

Can a hub nut still be used on a jeep?

On my Jeep I have aftermarket wheels so I am able to access the main hub nut with the wheel still on. With the nut torqued to 175ft/lbs and rust/dirt seizing up the nut, it isn’t a surprise that a cheater bar helps In this case it is my old tie rod.

Where is the hub on a Jeep front wheel?

Next, on the back side of the knuckle there are three bolts. They require a 12pt 13mm socket to remove them and can be stuck on there pretty good as well. The first one is at the top, then the other two are on the lower left and lower right (imagine a triangle): At this point you can remove the hub.

How big should axle nut be on Jeep Cherokee?

I also tend to use never-seez on the unit bearing retainer screws – then torque them to 37-38 pound-feet, vice the “clean, dry” spec of 75 pound-feet (so I can take those damned things off later if I need to as well!) Remember, if the FSM value doesn’t list a lubricant as required, it’s a “clean, dry” spec.

What causes damage to a Jeep Grand Cherokee CV axle?

Damage to your Jeep Grand Cherokee CV axle occurs when its protective boots have cracks that allow grease to escape and dirt to enter. Continuing to drive with a damaged CV joint boot causes irreparable damage to the CV joint, ultimately making the vehicle undrivable.

Where can I buy a Jeep Grand Cherokee axle?

Buy Online. Pick Up In-Store. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only Your Jeep Grand Cherokee is the chief of all SUVs, thanks to its roominess, dependability and versatility. Don’t let a potentially serious problem like a damaged Grand Cherokee drive axle go unchecked when new parts are available at AutoZone.

Where to get a new drive shaft for a Jeep Grand Cherokee?

Take action by replacing your drive shaft for Jeep Grand Cherokee so you can experience efficient turns and smooth driving. Order online and use Same-Day Store Pickup at the AutoZone location most convenient to you.

How to adjust caster on Jeep Grand Cherokee?

To maintain the camber angle while adjusting caster, move the rear of the lower control arm in or out. Then move the front of the lower control arm slightly in the opposite direction. Move both the front and rear of the lower control arm together in or out. This will change the camber angle signif-

How to search for custom Jeep Grand Cherokee wheels?

Search for 1000’s of Jeep Grand Cherokee Custom Wheels using our custom search tool for rims and tires. There has never been an easier or more complete wheel search available on any other website.

Why does my Jeep Grand Cherokee shake when I accelerate?

If your Jeep Grand Cherokee is shaking when accelerating, it’s something that should not be ignored. While the vibration can be annoying, it is often indicative of a serious problem. Vehicle speed matters when you feel a vibration. Different problems are going to show themselves when driving at different speeds.

How to replace the front axle seal on a Jeep Grand Cherokee?

2.Install the brake rotor shield to the knuckle. 3.Install the hub bearing and axle shaft assembly, or axle shaft, into the housing and differential side gears. Avoid damaging the axle shaft oil seals in the axle housing.

What kind of wheel hub do I need for my Jeep Grand Cherokee?

Jeep Grand Cherokee 2011, Rear Wheel Bearing by Mopar®. Put your wheel hub back to its to optimum condition with this top-notch replacement bearing component that will let your rim turn freely again. Replace your worn out or severely… Jeep Grand Cherokee with Dana 30 Series Axle 2011, Wheel Seal by Nitro Gear & Axle®.

How do you change wheel bearings on a Toyota Tundra?

On vehicles where the wheel bearing is pressed into a cavity within the steering knuckle, the steering knuckle must be removed from the vehicle in order to press out the old bearing and press in the new bearing. On some vehicles, the wheel bearing is pressed onto an axle shaft and thus the axle must be extracted from the axle carrier.

Navigation