What should the battery voltage be on a Jeep Patriot?
With no electricity loads you should get 14.5 v. If it’s at battery voltage, alternator failed. If different then broken cable. If varies to ground then maybe lost ground to engine. Also check pcm and control Twin wires not open circuit. On the Jeep, I would say order of failure probability is 1).
Where are the fuses located in a Jeep Patriot?
An Integrated Power Module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover. How to check the fuses?
When did the Jeep Patriot MK74 come out?
The compact crossover Jeep Patriot (MK74) was produced from 2007 to 2017. Here you will find fuse box diagrams of Jeep Patriot 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016 and 2017, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
Can you replace the battery in a Jeep Patriot?
Battery Replacement: 2007-2017 Jeep Patriot – 2012 Jeep Patriot Sport 2.0L 4 Cyl. 1. Getting Started – Prepare for the repair 2. Open the Hood – How to pop the hood and prop it open
An Integrated Power Module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover. How to check the fuses?
The compact crossover Jeep Patriot (MK74) was produced from 2007 to 2017. Here you will find fuse box diagrams of Jeep Patriot 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016 and 2017, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
What are the warning lights on a jeep?
The following are warning lights and indicators found in vehicles built by Jeep. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray), but there are nearly 80 of them so be patient!
What’s the service procedure for a Jeep Patriot?
Service Procedure NOTE: fThe StarSCAN tool software must be at version 7.04 or higher before this procedure can be performed. A. Program the TIPM 1. Open the hood and remove the inlet air duct over the battery. 2. Install a battery charger. Verify that the charging rate provides approximately 13.5 volts.
Where is the ignition key in a Jeep Patriot?
Before attempting service, the ignition key must have been inserted into the ignition lock cylinder. Then rotate the steering wheel from side to side. If the steering wheel can be rotated, the locking bolt is in the unlocked position. Leave the key in the ignition lock cylinder until shaft lock module removal has been completed.
How to turn off the ECU on a Jeep Patriot?
Turn the ignition key to the ON position, (Engine Off) b. Connect the scan tool (StarSCAN (R)) to the data link connector and turn the ignition to the RUN position, (engine off). c. Select “ECU View.” d.
With no electricity loads you should get 14.5 v. If it’s at battery voltage, alternator failed. If different then broken cable. If varies to ground then maybe lost ground to engine. Also check pcm and control Twin wires not open circuit. On the Jeep, I would say order of failure probability is 1).
Service Procedure NOTE: fThe StarSCAN tool software must be at version 7.04 or higher before this procedure can be performed. A. Program the TIPM 1. Open the hood and remove the inlet air duct over the battery. 2. Install a battery charger. Verify that the charging rate provides approximately 13.5 volts.
Before attempting service, the ignition key must have been inserted into the ignition lock cylinder. Then rotate the steering wheel from side to side. If the steering wheel can be rotated, the locking bolt is in the unlocked position. Leave the key in the ignition lock cylinder until shaft lock module removal has been completed.
Turn the ignition key to the ON position, (Engine Off) b. Connect the scan tool (StarSCAN (R)) to the data link connector and turn the ignition to the RUN position, (engine off). c. Select “ECU View.” d.